Features
- Very compact size: 29x29x10mm.
- Works with electric lock supplied from 9 to 24Vdc and from 9 to 18Vac, with max current 3.2Aac or 3.5Adc
- Frequency selected by the user: 433.92, 868, 315, 288, 300, 303, 306, 310, 318, 330, 390, 403.55, 418 MHz. The frequency of the remote control should be stable, so it does not work with remote controls without crystal or saw resonator!
- Works with a wide range of remote controls which transmit fixed or rolling code. See the compatibility table.
- Manages different types of remote controls in the same time.
- It's possible to learn one or more "master remote controls" that can be use just to enable learning for 10s without the need to access the receiver to press the Prog button.
This very small device, only 29x29x10mm, can be used with almost any radio remote control in the market which transmit in a frequency between 288 and 868 MHz.
It's very easy to be installed: only two wires that should be connected in parallel with the switch used to activate the electric lock. Get a low current through these 2 wires, and when it receive a previously learned code, it shorts this wires let current flowing through the electric lock.
The operating frequency, shown in the table, can be simply programmed using the Prog button, as like as the number of activating pulses (1, 2, 3, 4) and their length (100ms, 200ms, 400ms, 800ms).
In the same door opener it's possible to learn up to 60 different remote controls, even if different brand/model, both fixed and rolling code: the number of remote controls depends by the code complex, so, for example, it's possible to manage 60 12bit remote controls or 40 KeeLoq rolling code remote controls.
When a known code is transmitted by the remote control, Creasol UniLock shorts the supply wires, simulating a pushbutton: in this way the current through the electric lock will open it. It can manage current up to 3.2Aac or 3.5Adc, and voltage up to 18Vac or 24Vdc.
Creasol UniLock can be used to:
- open the main entrance door by almost any type of remote control
- open the pedestrian gate
- open any system which uses an electric lock
It's supplied in nice blister with instructions printed in several languages. We can also supply this device with customized instructions.
Installing instructions
This device has 3 wires, one of which is used as antenna and should not be connected anywhere. Two wires should be connected to the existing switch, so a little current (20mA) will pass through the electric lock supplying Creasol UniLock.
-
Check the voltage on the existing switch: it should be in the range 9÷24Vdc or 9÷18Vac.
-
Measure the current through the existing switch: it should be in the range 0,5÷3.2Aac or 0.5÷3.5Adc.
-
Connect the 2 wires marked as Supply in parallel to the existing switch.
- Configure the frequency you wish to use, pressing Prog button for 5 times: LED shows the current programmed frequency, for example it flashes twice to indicate 433.92 MHz. Then press again Prog button N times, as indicated in the frequency table (for example 3 times for 868.3 MHz).
- Configure the number of pulses, pressing Prog button 6 times: LED flashes to indicate the current configuration. Press Prog button again to set the desired number.
- Configure the pulse length, pressing Prog button 7 times: LED flashes to indicate the current configuration. Press Prog button again to set the desired length.
Press the Prog button twice to enable learning mode: then it's possible to press a button on the existing remote control, within 10s, to learn it. Every time a new code is learned, the 10s timeout is reload.
LED flashes 2 times if the remote control has been learned, 3 times if it was already learned, 6 times if memory is full.
Removing remote controlsPress the Prog button 3 times, then it's possible to transmit, within 10s, from the remote control that need to be removed: LED flashes 4 times indicating that the remote control has been removed.
Alternatively, to blank memory (remove all remote controls), press Prog button for 10 times, LED flashes 10 times, then press again Prog button 3 times.
Learning "master" remote controlsPress the Prog button 4 times and follow the same procedure to learn remote controls: in this case it's possible to learn one or more "master" remote control, which can be used only to enable the learning procedure remotely, without the need to press the Prog button. Note that "master" remote controls do NOT activate the door opener output.
To learn new remote controls in this way, put the "master" remote control in trasmission for 1-2 seconds, then start to transmit for 1-2 seconds from the new remote controls: every time a new remote control is learned, the 10s timer is reload to permit successive learnings.