Packing specification of BD65 crusher liner plate special backing adhesives:
  20Kg/group,packed in a iron drum, 10kg/group,packed in a plastic drum

product usage of BD65 crusher wear resistant protective filling adhesive:
BD65 backing adhesives(crusher lining plate filling adhesive) is used in the filling/supporting between crusher lining plate and substrates,gravel barrels and jacket gap,support cone and protective layer space,at the same time it can be used as buffer material,when the equipment suffers impacting or load vibration from broken ore, also used in the structural reinforcement,impact resistant vibration of ball mill wear resistant lining plate and cylinder gap.

performance features of BD65 lining plate abrasion resistant special filling material:
 Before curing: with good fluidity and strong filling ability,easy to operate,safety and environmental protection
 After curing: with low shrinking percentage and good adhesion,bearing capacity is high,can tear down

BD65 liner plate anti wear repair backing adhesive performance index:
  Modified epoxy material,two component,gray fluid
  Color: A component: gray, B component: brown
  Viscosity: A component: 40000, B component: 250±50mPa.s(GB/T2791-1995)
  Density:A component: 1.6, B component: 1.01g/cm3 (GB/T13354-1992)
  Compressive strength after curing:120 Mpa (GB/T2791-1995)
  Shear strength after curing:12.3 Mpa (GB/T7124-1996)
  Hardness after curing:Shore D85 (GB/T2144-1980)
  Shrinkage ratio after curing: 0.01%
  Cooperation ratio(A : B),weight ratio 8:1,volume ratio  5:1
  Pot life:15 min,the shortest curing time before operation:12h
  Operation temperature:5℃-30℃
  The temperature resistant after curing:-50℃-170 ℃

BD65 crusher anti abrasion special filling materials use technology
  1  Cleaning up and preparation:    Clean up the residual filling material of the cone surface,or greasy dirt and dirt from the parts where touch with adhesive.Fit up the cone and lining plate,seal up the cone/lining plate fitting surface and ring hole with adhesive tape etc,to avoid leaking adhesive,in necessity,protect the screw thread on the axis,construction is in the temperature of 5℃-30℃ as far as possible during using.General construction in winter,you had better heat the A component up to the temperature of 25℃-35℃ separately to reduce viscosity for easy to pour.For ease of disassembly next time,the cone and lining plate surface can precoat proper engine oil or mold release agent.
  2 Configure adhesive:    Make the blender fix on low speed electric hand drill,Open the A component of BD65,stir it for 1 minute,then pour the B component into the A component drum at the same time stir it with the electric blender,it's OK for color uniform,general stirring time is not more than 4 minutes.
Operation time:The total time from start mixing to finish filling is not more than 15 minutes(the data for 20℃)
  3  Pouring:   Make the mixed-up BD65 adhesive solution pour into it along the cone or a place of lining plate crack,easy to exhaust,in necessity,can make a cofferdam guide with plasticine etc,until overflow from the top of crack.Don't pour into the adhesive without mixing uniformly(with different colors)
  4 Curing:   Place to cure for 12-24 hours,the temperature makes a big difference for the curing time,the curing speed is fast for high temperature,it can put into using to cure for 12 hours in summer,and cure for 24 hours in winter.

Notes:
1.  The operation temperature of BD65 backing adhesive is 5℃-30℃,try not to construct,if the temperature of cone is below 5℃ or above 30℃.
2.  If the temperature is too low,the operation time can be long,but it's difficult to pour for the high viscosity,if the temperature is below 10℃,can heat the A component of BD65 adhesive up to the temperature of 25℃,then stir it for using.
3.  If the temperature is too high,reduce the operation time,the pouring time is short,if the temperature is above 25℃,can reduce configured adhesive quantity for once,it's while pouring and configuring material.

storage of BD65 crusher lining plate special abrasion resistant protective adhesives:
 BD65 backing adhesive is the general chemicals,should pay attention to waterproof and preventing fire in the process of transportation and storage,stored in a cool and dry place,the storage period is 1 year.