Interpreter Console
The TC-F06 interpreter console is a digitally-controlled workstation allowing two interpreters to work in turn.
Handles simultaneous interpretation for up to 6 different languages.
Gooseneck microphone and headset microphone can be used
Built-in loudspeaker with volume level control
LCD screen for specific information display
3.5mm jacks on both sides for MIC input and headphone/recording output
3 incoming languages can be preset, with pre-select A/B/C keys.
Automatic channel interlocking prevents interpreters from using same outgoing channel
Relay interpretation allows the interpreters to work from an active channel other than the floor
MUTE key to enable a brief muting of the microphone for cough cut
SLOW key to alert the current speaker to speak slowly
Loudspeaker is automatically switched off when MIC is on or headset is used
The floor signal automatically goes to the output channel after the microphone is switched off
Multiple interpreter consoles can be connected in a daisy-chain
Designed to comply with all related international standards & requirements.
|
Frequency response: 50-18kHz
Distortion at 1 kHz: < 0.1%
Channel separation: > 85 dB
Signal-to-noise ratio: > 90 dB
Max. input power level: 7.5V
Operating voltage: 24V
Power consumption: 2.5W |
8Ω/2W built-in loudspeaker
Operating temperature: 0℃-50℃
Standard mic stem length: 425 mm
128x64 backlit LCD screen
3/5/10m cable with DB25 connectors
3.5mm jacks for mic, headphone, recorder
ABS base: 247 X 145 X 95mm |
IR Transmitter
The TC-Z902V/Z904V/Z906V infrared transmitter is a microprocessor based central unit which is designed to modulate and transmit 2/4/6 sound channels to different carrier frequencies. It features built-in IR test diodes for audio monitoring and testing of receivers, independent channel volume control, independent channel output level indicators, and independent channel audio output for sound recording. Test mode produces a different frequency tone for each input/channel. Two BNC sockets can link up infrared radiators in two lines. Multiple interpreter consoles can be connected to the transmitter in a daisy chain.
|
Modulation mode: FM
Frequency synthesis: digital PLL
Frequency band: 2.0 - 6.0MHz
Frequency response: 100-14kHz
Frequency stability: 10ppm
Pre-emphasis: 75 μSec.
Peak deviation: ±7.5kHz
Distortion at 1 kHz: <0.5%
Channel separation: >70dB
RF output power level: 700mV |
RF output impedance: 55-75 ohms
Input impedance: 18k ohms
Max. input power level: 7.5V
AGC range: 30dB
S/N ratio: >75dB
Power consumption: 40W
Powe requirement: 110/240VAC, 50-60Hz
19" rack mountable case
Dimension: 430×99×325 mm (W×H×D)
|
IR Radiator
The TC-H15 high-power infrared radiator can be switchable to 50% low power, making it suitable for use in larger halls and smaller rooms. The radiator’s integrated power supply unit is automatically switched on and off by the carrier signals from the transmitter by means of an high frequency sensor. The radiator is equipped with automatic gain control to ensure the infrared diodes function with maximum efficiency, and is naturally convection cooled for totally silent and maintenance-free continuous operation. It can be ceiling or wall mounted for permanent installation, or set up on an optional tripod for portable application.Multiple radiators can easily be daisy-chained together to expand coverage. The unit is easy to maintain and clean, with IR emitting diodes protected by the cover plate.
|
Frequency band: 2.0 - 6.0 MHz
IR output power: 15W
Switchable output level: Low/High
Coverage range: up to 30 meters
Angle of half intensity: ±22°
RF output impedance: 55-75 ohms |
RF input voltage: 100-2000mV
Power consumption: 55W, Stand-by 8W
Power Supply: 110/240VAC, 50/60Hz
Operating temperature: 0℃-40℃
Cable: 75Ω-4 coax, BNC connectors
Dimensions: 450×211×82 mm |
IR Receiver
The portable TC-J902/J904/J906 infrared receiver is designed to receive 2/4/6 audio channels. The optical lens offers a wider receiving angle to pick up the infrared light signal. The delegate may listen to any selected language on a headphone/earphone. Volume level can be adjusted through the volume control for comfortable listening. Any number of receivers can be used in an installation.
|
Modulation mode: FM
Frequency synthesis: digital PLL
Frequency band: 2.0 - 6.0MHz
Frequency response: 100-14kHz
De-emphasis: 75 μSec.
Peak deviation: ±7.5kHz
Distortion at 1 kHz: <1%
S/N ratio: >55dB
|
Frequency stability: 10ppm
Operating voltage: 2.3V-3.6V
Power consumption: 50mW
Slide switch for channel selection
Switch for power on/off & volume control
3.5mm earphone output jack
Battery type: 2 x AAA alkaline or rechargeable
Pocket clip and lanyard for easy-wearing
Dimensions: 140×58×30 mm (LxWxD) |
IR Receiver
The portable TC-J902L/J904L/J906L infrared receiver is designed to receive 2/4/6 audio channels. The unit is powered by a more environment-friendly rechargeable Lithium-ion battery pack. The selected channel number and battery level can be displayed on LCD screen. The user may listen to any selected language on a personal earphone. Volume level can be adjusted through a thumbwheel switch for comfortable listening. Any number of receivers can be used within the radiator's effective coverage range in an installation.
|
Slide switch for power on/off
Thumbwheel switch for volume control
3.5mm phone output jack
Up/down push buttons for channel selection
LCD shows channel number & battery level
Pocket clip and lanyard for easy-wearing
Rechargeable Li-ion battery pack included
Integrated charging electronics & contacts
Modulation mode: FM
Frequency synthesis: digital PLL |
Carrier frequencies: 2.0 - 6.0MHz
Frequency response: 100-14kHz
De-emphasis: 75 μSec.
Peak deviation: ±7.5kHz
Distortion at 1 kHz: <1%
S/N ratio: >55dB
Channel separation: >55dBA
Frequency stability: 10ppm
Operating voltage: 3.7V
Power consumption: 50mW |
Charging Case GX-20
Designed to be used for charging and storage of receiver units
Accommodates up to 20 receiver units with Li-ion battery packs
Microprocessor-based unit w/ smart charging circuit
DC 5V low voltage charging power
Independent LED indicators for charging status
About 10 hours needed to fully recharge 20 receivers
Receivers can be left in the case after the charge is complete
AC/DC adaptor w/ power cord
Power input AC100-240V 50/60Hz, output DC5V 8A
Dimensions: 59x30x18 cm (LxDxH)
Interpreter Headset TC-D2
Closed-ear stereo headset with mic & vol control
Connectors: 3.5mm stereo plugs
Impedance: 60Ω±15%
Frequency response: 20Hz to 20KHz
Input power: 30-50mW
Sensitivity (1 kHz): -58±2dB
Microphone type: Omni-directional dynamic
Microphone sensitivity (1 kHz): -58±2dB
Cord length: 2 meters
Delegate Earphone TC-D1
Single clip-on mono earphone
3.5mm mini plug
Impedance: 40Ω±10%
Sensitivity: 102dB
Frequency response: 7Hz to 24KHz
Input power: 8-50mW
Cord length: 120 cm
Full range enhance system
Super bass frequency technology
Configuration Diagram
