| item | YG-JZ-10 | YG-JZ-15 | YG-JZ-20 | YG-JZ-25 | YG-JZ-30 | YG-JZ-35 | YG-JZ-40 |
| Run by electriciy | 550 | 600 | |||||
|
max. gas energy consumption |
5*106 KJ/h | 5*106 KJ/h | 6*106 KJ/h | 8*106 KJ/h | 10*106 KJ/h | 10*106 KJ/h | 11*106 KJ/h |
| max. using temp | 620 | 620 | 620 | 620 | 620 | 620 | 620 |
| heating zone size | 6500*1200*1100 | 6500*1800*1100 | 6500*2000*1300 | 6500*2200*1500 | 6500*2200*1800 | 6500*2200*2200 | 6500*2350*2300 |
| recycle blower | 3*30 | 3*45 | 3*45 | 3*45 | 3*45 | 3*(55/75) | 3*(55/75) |
| outside size | 8000*5650*4980 | 8000*6460*4980 | 8000*6700*5300 | 8000*6800*5500 | 8000*6800*5800 | 8000*7280*7860 | 8000*7560*7800 |
|
billet QTY in each furnace |
50(dia. 127) | 84(dia. 127) | 105(dia. 127) | 125(dia. 127) | 150(dia. 127) | 135(dia. 143) | 160(dia. 143) |
| billet weight | 10000 | 16600 | 20700 | 25000 | 30000 | 35100 | 41000 |
| 3D charging car | |||||||
| rated loaded capacity | 10000 | 15000 | 20000 | 25000 | 30000 | 35000 | 40000 |
| hydraulic station motor | 4 | 5.5 | 5.5 | 5.5 | 5.5 | 7.5 | 7.5 |
| cooling room | |||||||
| cooling wind volumne | 1.68*105 | 1.68*105 | 1.68*105 | 1.68*105 | 2.54*105 | 2.54*105 | 2.54*105 |
| cooling water flow | 2.4-6 | 2.4-6 | 2.4-6 | 2.4-6 | 5.0-10 | 5.0-10 | 5.0-10 |
| cooling area | 6500*1200*1100 | 6500*1800*1100 | 6500*2000*1300 | 6500*2200*1500 | 6500*2200*1800 | 6500*2200*2200 | 6500*2500*2300 |
During the casting course of aluminum rods, the chemical constituents and structure inside the rod may present heterogeneous phenomenon, also the inside generally has residual stress. To remove the residual stress of casting and the heterogeneous phenomenon, some uniform treatment is needed to improve the press-working manufacturability of castings and guarantee certain final performance of the products. This uniform treatment of ingot is conducted inside the homogenizing furnace.
The hot blast circulatory system inside the homogenizing furnace adopts several high-capacity fans paralleled together to assure minimal temperature difference..
The heating system of the homogenizing furnace adopts several burners for multipoint heating at the same time, because of the proportional control of burner heating, complete burning can be guaranteed and the furnace temperature uniform.
Material filling and discharging of the homogenizing furnace is completed through complex 3-d car which can move flexibly at all directions, thus the filling and discharging course finished automatically.
The cooling system of the homogenizing furnace is combined with air cooling and water cooling, which can achieve good effect even under low cost.