|
MODEL |
NES-15-12 | |
|
OUTPUT |
DCVOLTAGE |
12V |
|
RATEDCURRENT |
1.3A | |
|
CURRENTRANGE |
0~1.3A | |
|
RATEDPOWER |
15.6W | |
|
RIPPLE&NOISENOTE.2 |
150MVP-P | |
|
VOLTAGEADJ.RANGE |
10.8~13.2V | |
|
VOLTAGETOLERANCENOTE.3 |
±1.0% | |
|
LINEREGULATION |
±0.5% | |
|
LOADREGULATION |
±0.5% | |
|
SETUP.RISEHOLD.TIME |
1000ms,30ms/230VAC ,1000ms, 30ms/115VAC at fill load | |
|
INPUT |
VOLTAGERANGE |
85~264VAC 120~370VDC |
|
FREQUENCYRANGE |
47~63HZ | |
|
EFFICIENCY |
81% | |
|
AC CURRENT |
0.35a/115vac 0.25a/230vac | |
|
INRUSH CURRENT |
Cold start 45A | |
|
LEAKAGECURRENT |
<2mA/240VAC | |
|
PROTECTION |
OVERLOAD |
Above 105~150%rated outputpower |
|
Protection type：Hiccup mode,recovers automatically after temperature goes down | ||
|
OVER VOLTAGE |
13.8~16.2V | |
|
Protection type：Shut off | ||
|
OVER TEMPERATURE |
U1 Tj 140℃ typically(U1) Detect on main control IC | |
|
Proterction type:Shut down o/p voltage recovers automatically after temperature goes down | ||
|
ENVIRONMENT |
WORKINGTIMP |
-20~+60℃ |
|
WORKINGHUMIDITY |
-20~90%Rhnon-condensing | |
|
STORAGE TEMP HUMIDITY |
-40~+85℃ 10~95%RH | |
|
TEMPCOEFFICIENT |
±0.03%(0~45℃) | |
|
VIBRATION |
10~500HZ,2G10min/1cycle period for 60 min each alongX,Y,Zaxes | |
|
SAFETY&EMC |
SAFETYSTANDARDS |
UL60950-1 Approved,CB Approved by TUV(design Refer to IEC 60950-1) |
|
WITHSTAND VOLTAGE |
1/P-0/P:3KVAC 1/P-FG:1.5KVAC 0/P-FG:0.5KVAC | |
|
ISOLATIONRESISTANCE |
1/P-0/P,1/P-FG,0/P-FG:100M Ohms/500VDC | |
|
EMI CONDUCTICN&
RADIATION |
Compliance to EN55022(CISPR22)classB | |
|
HARMONICCURRENT |
Compliance to EN61000-3-2,-3 | |
|
EMS IMMUNITY |
Compliance to EN61000-4-2,3,4,5,6,8,11 ENV50204,EN50204,EN61000-6-1 Light industry level criteriaA | |
|
QTHERS |
MTBF |
563.5. Khrs min MIL-HDBK-217F(25℃) |
|
DIMENSION |
79*51*28mm(L*W*H) | |
|
PACKING |
0.18Kg 60pcs / 14Kg / 0.57CUFT | |
|
NOTE |
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Line regulation is measured from low line to high line at rated load.
5. Load regulation is measured from 0% to 100% rated load.
6. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
| |
