|
MODEL |
NED-35A | ||
|
OUTPUT |
OUTPUT NUMBER |
CH1 |
CH2 |
|
DCVOLTAGE |
5V |
12V | |
|
RATEDCURRENT |
4A |
1A | |
|
CURRENTRANGE |
0.5~5A |
0.1-1.5A | |
|
RATED POWER |
32W | ||
|
RIPPLE&NOISENOTE.2 |
80MVP-P |
120mVp-p | |
|
VOLTAGEADJ.RANGE |
CH1: 4.75~5.5V | ||
|
VOLTAGETOLERANCENOTE.3 |
±2.0% |
±6.0% | |
|
LINEREGULATION |
±1.5% |
±1.0% | |
|
LOADREGULATION |
±0.5% |
±3.0% | |
|
SETUP.RISEHOLD.TIME |
500ms,30ms/230VAC ,1200ms, 30ms/115VAC at full load | ||
|
HOLD TIME |
50ms/230vac 10ms/115vac at full load | ||
|
INPUT |
VOLTAGERANGE |
85~264VAC 120~370VDC | |
|
FREQUENCYRANGE |
47~63HZ | ||
|
EFFICIENCY |
78% | ||
|
AC CURRENT |
0.75a/115vac 0.5a/230vac | ||
|
INRUSH CURRENT |
Cold start 45A | ||
|
LEAKAGECURRENT |
<2mA/240VAC | ||
|
PROTECTION |
OVERLOAD |
Above 110~150%rated outputpower | |
|
Protection type：Hiccup mode,recovers automatically after fault condition is removed | |||
|
OVER VOLTAGE |
5.75~6.75V | ||
|
Protection type：Shut odown o/p voltage,re-power on to recover | |||
|
ENVIRONMENT |
WORKINGTIMP |
-20~+60℃ | |
|
WORKINGHUMIDITY |
20~90% RH non-condensing | ||
|
STORAGE TEMP HUMIDITY |
-40~+85℃ 10~95%RH | ||
|
TEMPCOEFFICIENT |
±0.03%(0~45℃) | ||
|
VIBRATION |
10~500HZ,2G10min/1cycle period for 60 min each alongX,Y,Zaxes | ||
|
SAFETY&EMC |
SAFETYSTANDARDS |
UL60950-1 Approved,CB Approved by TUV(design Refer to IEC 60950-1) | |
|
WITHSTAND VOLTAGE |
1/P-0/P:3KVAC 1/P-FG:1.5KVAC 0/P-FG:0.5KVAC | ||
|
ISOLATIONRESISTANCE |
1/P-0/P,1/P-FG,0/P-FG:100M Ohms/500VDC | ||
|
EMI CONDUCTICN&
RADIATION |
Compliance to EN55022(CISPR22)classB | ||
|
HARMONICCURRENT |
Compliance to EN61000-3-2,-3 | ||
|
EMS IMMUNITY |
Compliance to EN61000-4-2,3,4,5,6,8,11 ENV50204,EN50204,EN61000-6-1 Light industry level criteriaA | ||
|
QTHERS |
MTBF |
394 Khrs min MIL-HDBK-217F(25℃) | |
|
DIMENSION |
99*97*36mm(L*W*H) | ||
|
PACKING |
0.36Kg 45pcs / 17.2Kg / 0.9CUFT | ||
|
NOTE |
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Line regulation is measured from low line to high line at rated load.
5. Load regulation is measured from 0% to 100% rated load.
6. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
| ||
