G8.5 Single-ended Ceramic Metal Halide Lamp (CDM-T 35W/70W).You can learn more about the lamp from gdutkk at hotmail.
|
Features:
|
It is a new generation of super performance light source, integrated with high color rendering index, high luminous efficiency, and long life
To adopt polycrystalline alumina ceramic bulb, with light transmittance up to 98% Without the problem of sodium permeation, the parameters of its luminous efficiency, color temperature, color rendering of the lamp are stable during whole lifetime To adopt UV-prevent block quartz glass as out envelop, take off the harm of UV radiation |
|
Advantages:
|
High light efficiency, less consumption
Long life of over 8000 hours, low cost of maintenance and replacement High color rendering, show the true color of the product Low loss of heat energy, comfortable lighting environment Anti-UV quartz outer envelope, reduce the UV radiation |
|
Applications:
|
To replace incandescent lamps and halogen lamps, used in commercial lighting, public place and leisure place that are with high request of color rendering
Used for lighting in community facilities, floodlighting, indoor lighting, etc. The best suitable light source for solar lighting adllighting.com(AT)HID |
Introduction to use:
1.The lamps should be worked with ignitor,ballast,fitting which is eligible and has correct mark.
2.It will take about 5 minutes from initially lighting to high luminance.
3.Working voltage:voltage change in short time is allowable as ±5% of the rated voltage marked by the fitting.The average working voltage should not exceed 3% of the rate voltage.
4.Color deviation:Several lamp's color difference may occur on all metal hallde lamps.This kind of color deviation may be caused by exterior effect. For example supplying voltage,collocation of the electric, lighting position etc.
5.Please do not touch the lamp which was just taken off,do not install or take off the lamp until the lamp is cool,and please turn off the power firstly when it is going to be installed.
6.When it has the following phenomenons,life of the lamp is end.
-The color of the lamp change obviously;
-The brightness of lamp becomes very dark;
-The lamp starts and went out intermittently;
-The lamp can't start;
7.When install the new lamp,please clean the lamp with the soft cloth,to clean such as fingerprint and dust.
8.To avoid explosion,please do not harm the glass envelop or dripping water on it.Please use the fitting with cover,if the lamp is damaged,please replace it immediately.
1.The lamps should be worked with ignitor,ballast,fitting which is eligible and has correct mark.
2.It will take about 5 minutes from initially lighting to high luminance.
3.Working voltage:voltage change in short time is allowable as ±5% of the rated voltage marked by the fitting.The average working voltage should not exceed 3% of the rate voltage.
4.Color deviation:Several lamp's color difference may occur on all metal hallde lamps.This kind of color deviation may be caused by exterior effect. For example supplying voltage,collocation of the electric, lighting position etc.
5.Please do not touch the lamp which was just taken off,do not install or take off the lamp until the lamp is cool,and please turn off the power firstly when it is going to be installed.
6.When it has the following phenomenons,life of the lamp is end.
-The color of the lamp change obviously;
-The brightness of lamp becomes very dark;
-The lamp starts and went out intermittently;
-The lamp can't start;
7.When install the new lamp,please clean the lamp with the soft cloth,to clean such as fingerprint and dust.
8.To avoid explosion,please do not harm the glass envelop or dripping water on it.Please use the fitting with cover,if the lamp is damaged,please replace it immediately.
ADL Lighting Co.,Ltd is established in Apr.2000.which covers an area of 50000 M2 and registered capital of 10 million yuan,with 13 integrative flow production lines,and advanced test equipments.Now We produce metal halide lamp series and its match products professionally,including MH lighting fixture series,35W~400W metal halide lamp lighting source series,35W~150W MH electronic ballast,35W~400W magnetic ballast and so on matching.We can produce any products according to customer's requirement,all products well sold in Europe,America,Southeast Asia,Africa,Middle East etc,ADL has passed ISO9001 in 2001,products have been approvaled by CE,ROHS,CCC and so on certification.Offer OEM and ODM service.