Ford mazda jaquar land rover IDS / VCM
The Vehicle Communication Module (VCM) is a high performance, ruggedized, vehicle serial communications gateway. This device provides multiple vehicle serial communication interfaces to meet the requirements of all Ford Motor Company vehicles.
The Ford Integrated Diagnostic System (IDS) will be the only equipment that provides complete diagnostic coverage of current and future Ford, Lincoln and Mercury vehicles in North America.
The IDS package replaces the Worldwide Diagnostic System (WDS). The IDS application will perform the identical functions of the WDS and allows dealership technicians to diagnose and service Ford, Lincoln, Mazda, Mercury, Land Rover & Jaguar vehicles.
Diagnostic Functionality
** For incode calculate by using this tool, pleaes refer to INCODE => OUTCODE
Self Test
Retrieve CMDTC's
KOEO (Key-On-Engine-Off)
KOER (Key-On-Engine-Running)
Data Logger
Body
Chassis
Electrical
Powertrain
Pressure/Vacuum Tests
Network Test
Module Programming
Programmable Module Installation
Module Reprogramming
Programmable Parameters
Body Tools
PATS Functions
Remote Keyless Entry
Factory Keyless Entry Code
Restraints
Chassis Tools
ABS Service Bleed
IVD Initialization Sequence
Ride Height Calibration
Pneumatic Test
Accurate Trim Test
Electrical Tools
Charging System Test
Parking Aid Switch Test
Audio
Powertrain Tools
EVAP Test
Fuel Economy Test
Fuel System Test/Relative Injector Flow Test
(IDS - Some vehicles require only VCM)
Ignition System Test
Spark Duration PIDs
Power Balance Test
Relative Compression Test
Transmission Test
(IDS - Some vehicles require only VCM)
Engine Checks and OBD Tests
(Drive Cycle, Mode 01, Mode 06 & Mode 09)
EGR Test
Other Powertrain tests & functions
Digital Multimeter
Basic DMM functions
(Volts, resistance, frequency)
Current measurements (50 Amps/500 Amps)
Pressure/Vacuum measurements with PVT
Oscilloscope Tools
Oscilloscope
Alternator ripple
COP (Coil-On-Plug) stress test
Signal Generator Monitor (SGM)
Vehicle Data Recorder (VDR)
Application Overview
Integrated Diagnostic Software (IDS) is the next generation diagnostic tool. IDS integrates WDS software modified to run on an off-the-shelf laptop with the Vehicle Communication Module (VCM) currently used in NGS+ and PDS, and a new Vehicle Measurement Module (VMM).
Vehicle Diagnostic Connectors
The VCM 16-pin DLC cable is used to connect the VCM to the vehicle. The VCM and VMM connect to the laptop through the Ethernet-USB Adapter Cable (H406/H416).
Interface Devices
The interface devices that are used with this application are:
1.VCM Vehicle Communication Module: This device provides all link based functionality including: Data logger, Self test, Service Functions, Module Configuration and Programming, etc.
2.VMM Vehicle Measurement Module :This device provides the following functionality: Oscilloscope, Digital Multi-Meter, Ignition System Test, Fuel System Test, and SGM.
Note that the application will detect the interface device that is connected to the laptop. Indicator icons will appear at the bottom right-hand corner of the IDS screen when the VCM and/or VMM are connected.
Supported languages:
English, German, French, Italian, Spanish, Netherlands, Swedish, Danish, Norwegian, Portuguese, Slovak
Ford VCM IDS Package includes:
1 Vehicle communication module - VCM
2 16-pin DLC long cable
3 IDS 4m PC Ethernet-USB host cable
4 DVD V70 (Ford/Mazda)
5 DVD V124(Land Rover/Jaguar)
The Vehicle Communication Module (VCM) is a high performance, ruggedized, vehicle serial communications gateway. This device provides multiple vehicle serial communication interfaces to meet the requirements of all Ford Motor Company vehicles.
The Ford Integrated Diagnostic System (IDS) will be the only equipment that provides complete diagnostic coverage of current and future Ford, Lincoln and Mercury vehicles in North America.
The IDS package replaces the Worldwide Diagnostic System (WDS). The IDS application will perform the identical functions of the WDS and allows dealership technicians to diagnose and service Ford, Lincoln, Mazda, Mercury, Land Rover & Jaguar vehicles.
Diagnostic Functionality
** For incode calculate by using this tool, pleaes refer to INCODE => OUTCODE
Self Test
Retrieve CMDTC's
KOEO (Key-On-Engine-Off)
KOER (Key-On-Engine-Running)
Data Logger
Body
Chassis
Electrical
Powertrain
Pressure/Vacuum Tests
Network Test
Module Programming
Programmable Module Installation
Module Reprogramming
Programmable Parameters
Body Tools
PATS Functions
Remote Keyless Entry
Factory Keyless Entry Code
Restraints
Chassis Tools
ABS Service Bleed
IVD Initialization Sequence
Ride Height Calibration
Pneumatic Test
Accurate Trim Test
Electrical Tools
Charging System Test
Parking Aid Switch Test
Audio
Powertrain Tools
EVAP Test
Fuel Economy Test
Fuel System Test/Relative Injector Flow Test
(IDS - Some vehicles require only VCM)
Ignition System Test
Spark Duration PIDs
Power Balance Test
Relative Compression Test
Transmission Test
(IDS - Some vehicles require only VCM)
Engine Checks and OBD Tests
(Drive Cycle, Mode 01, Mode 06 & Mode 09)
EGR Test
Other Powertrain tests & functions
Digital Multimeter
Basic DMM functions
(Volts, resistance, frequency)
Current measurements (50 Amps/500 Amps)
Pressure/Vacuum measurements with PVT
Oscilloscope Tools
Oscilloscope
Alternator ripple
COP (Coil-On-Plug) stress test
Signal Generator Monitor (SGM)
Vehicle Data Recorder (VDR)
Application Overview
Integrated Diagnostic Software (IDS) is the next generation diagnostic tool. IDS integrates WDS software modified to run on an off-the-shelf laptop with the Vehicle Communication Module (VCM) currently used in NGS+ and PDS, and a new Vehicle Measurement Module (VMM).
Vehicle Diagnostic Connectors
The VCM 16-pin DLC cable is used to connect the VCM to the vehicle. The VCM and VMM connect to the laptop through the Ethernet-USB Adapter Cable (H406/H416).
Interface Devices
The interface devices that are used with this application are:
1.VCM Vehicle Communication Module: This device provides all link based functionality including: Data logger, Self test, Service Functions, Module Configuration and Programming, etc.
2.VMM Vehicle Measurement Module :This device provides the following functionality: Oscilloscope, Digital Multi-Meter, Ignition System Test, Fuel System Test, and SGM.
Note that the application will detect the interface device that is connected to the laptop. Indicator icons will appear at the bottom right-hand corner of the IDS screen when the VCM and/or VMM are connected.
Supported languages:
English, German, French, Italian, Spanish, Netherlands, Swedish, Danish, Norwegian, Portuguese, Slovak
Ford VCM IDS Package includes:
1 Vehicle communication module - VCM
2 16-pin DLC long cable
3 IDS 4m PC Ethernet-USB host cable
4 DVD V70 (Ford/Mazda)
5 DVD V124(Land Rover/Jaguar)