UST104R-2F
100-1600m 4CH 1-2 Active Video Splitting Receiver Hub
Brightness Sharpness COMBO (BSCTM) Tool Free Control, Power Path Output, Femal BNC, Screw Terminal Block Connector
Transient Surge, Lightning Protection
Metal Housing +12VDC/500mA Power Supply
UST104R-2
100-1600m 4CH 1-2 Active Video Splitting Receiver Hub
Code Switches Gain/EQ ADJ, Simple Installation
Femal BNC, Screw Terminal Block Connector
Transient Surge, Lightning Protection
Metal Housing +12VDC/500mA Power Supply
Introduction
UST104R-2 / UST104R-F2 UTP CAT5 Video Receiver is an active (amplified) device that allows the extension of real-time monochrome or color video on up to 4000ft ,using Category-5 Unshielded Twisted-Pair (UTP) CAT5 networking wire. Baseband (composite, PAL/NTSC/SECAM) signals of any type are supported.
The unparalleled interference rejection and low emissions of the Model UST101T UST104T & UST104R-2 allows long run video signals to co-exist in the same wire bundle as telephone, datacom, or low-voltage power circuits. This allows the use of shared or existing cable plant. Ground-lifting ensures no annoying "hum-bars" when ground potential differences exist. With built-in lightning protection,transient protection, ESD protection,damaging voltage spike problems are eliminated.Equipment
Specifications
Cable Distance:Up to 5000ft Transmitter-Receive UTP Cat 5 or better.
Point to Point transmission of real-time PAL,NTSC or SECAM 04 channel CVBS video signals.
Image figure enhanced function in output of CAT5 video receiver.
Single potentiometer as fine Gain/EQ for each channel ADJ - UST104R-F2
Single 4-step code switch as easy Gain/EQ setting-up for each channel ADJ - UST104R-2
Lightning protection, Transient protection, ESD protection, Power Line Contact protection, damaging voltage spike problems are eliminated.
Dimensions: 170X90X33mm, GND screw connector.
Technical Specifications
Video Frequency Response DC to 6 MHz.
Power Supply Range
100-1600m 4CH 1-2 Active Video Splitting Receiver Hub
Brightness Sharpness COMBO (BSCTM) Tool Free Control, Power Path Output, Femal BNC, Screw Terminal Block Connector
Transient Surge, Lightning Protection
Metal Housing +12VDC/500mA Power Supply
UST104R-2
100-1600m 4CH 1-2 Active Video Splitting Receiver Hub
Code Switches Gain/EQ ADJ, Simple Installation
Femal BNC, Screw Terminal Block Connector
Transient Surge, Lightning Protection
Metal Housing +12VDC/500mA Power Supply
Introduction
UST104R-2 / UST104R-F2 UTP CAT5 Video Receiver is an active (amplified) device that allows the extension of real-time monochrome or color video on up to 4000ft ,using Category-5 Unshielded Twisted-Pair (UTP) CAT5 networking wire. Baseband (composite, PAL/NTSC/SECAM) signals of any type are supported.
The unparalleled interference rejection and low emissions of the Model UST101T UST104T & UST104R-2 allows long run video signals to co-exist in the same wire bundle as telephone, datacom, or low-voltage power circuits. This allows the use of shared or existing cable plant. Ground-lifting ensures no annoying "hum-bars" when ground potential differences exist. With built-in lightning protection,transient protection, ESD protection,damaging voltage spike problems are eliminated.Equipment
Specifications
Cable Distance:Up to 5000ft Transmitter-Receive UTP Cat 5 or better.
Point to Point transmission of real-time PAL,NTSC or SECAM 04 channel CVBS video signals.
Image figure enhanced function in output of CAT5 video receiver.
Single potentiometer as fine Gain/EQ for each channel ADJ - UST104R-F2
Single 4-step code switch as easy Gain/EQ setting-up for each channel ADJ - UST104R-2
Lightning protection, Transient protection, ESD protection, Power Line Contact protection, damaging voltage spike problems are eliminated.
Dimensions: 170X90X33mm, GND screw connector.
Technical Specifications
Video Frequency Response DC to 6 MHz.
Distance Switch 4-Position Adjustable for each channel.
Common-mode / Differential-mode Rejection 15KHz to 5 MHz 60 dB typ.
Line Impedance
Line Impedance
Coax, female BNC 75 ohms.
UTP, Terminal Block 100 ohms.
Wire Type
Wire Type
Network Wiring 2 Unshielded Twisted Pair 24-16 AWG (0.5-1.31mm).
Category Type Cat 5 or better.
Impedance 100 ± 20 ohms.
DC Loop Resistance 52 ohms per 1,000 ft (18 ohms per 100 m).
Differential Capacitance 19 pF/ft max (62 pF/m max).
LED Indicators
LED Indicators
Power On Red Indicator Light.
Power Supply Range
Transmitter/Receiver: 9-12V AC/DC (MAX 24V AC/DC) DC/AV 9-12V 500 mA MAX (24VAC/DC).
Environmental
Environmental
Temperature 0°C to +50° C.
Humidity (non-condensing) 0 to 95%.
Transient Immunity
Transient Immunity
6,000 V 1.2µS x 50 µS per ANSI/IEEE 587 C62.41 B3.
3,000 V 8µS x 20 µS when ground screw terminal is bonded to earth-ground.
Installmen
3,000 V 8µS x 20 µS when ground screw terminal is bonded to earth-ground.
Installmen
1:Put the video signals you need in the VIDEO IN of UST101T (or UST104T).
2: Put a twisted-pair in the each channel VIDEO A, B of UST104R-2/ UST104R-F2.
2: Put a twisted-pair in the each channel VIDEO A, B of UST104R-2/ UST104R-F2.
3: Connect with the mains following instructions shown in the sketch map, make sure that the power should be between DC/AC 9 to 24V. Recommend work in DC 12V.
Recommend to share 12V DC power supply with camera in transmitter termination.
Recommend to share 12V DC power supply with camera in transmitter termination.
4: Set the position of ADJ correctly according to the distance table in UST101T(or UST104T) & UST104R-2/ UST104R-F2 sub-surface.
5: After the four steps, the VIDEO output of UST104R-2/ UST104R-F2 is ready to work..
Check After Connection
Check After Connection
1. Power On Red LED Indicator Light.
2. Make sure that every wire is correctly and firmly connected.
Mechanical
Dimensions no excluding BNC 170mm×90mm ×55mm.
Material Metal
3 Year Warranty
3 Year Warranty