UST108R-S
100-1600m 08CH Active Video Receiver Hub
Brightness Sharpness COMBO (BSCTM) Tool Free Control
Femal BNC, Screw Terminal Block Connector
Transient, Lightning Protection
19“ 1U Mounting Rack, 12VDC/24VAC Supply, Power Path
UST108R
100-1600m 08Ch Active Video Receiver Hub
Code Switches Gain/EQ ADJ, Simple Installation
Femal BNC, Screw Terminal Block Connector
Transient Surge, Lightning Protection
Metal Housing +12VDC/500mA Power Supply
UST108R-2F
100-1600m 08CH 1-2 Active Video Splitting Receiver Hub
Brightness Sharpness COMBO (BSCTM) Tool Free Control
Femal BNC, Screw Terminal Block Connector
Transient, Lightning Protection
19“ 1U Mounting Rack, 110/220VAC Power (Fuse, Power Switch
Introduction
UST108R,UST108R-S, and UST108R-2F, 08 Channel CAT5 Video Receiver/Hub and 08 Channel 1-2Port CAT5 Video Receiver/Hub are active (amplified) pair equipments that allows the extension of real-time monochrome or color video on up to 4000ft (with Image figure enhanced function), using Category-5 Unshielded Twisted-Pair (UTP) CAT5 networking wire. Composite Video Broadcasting Base band (composite-CVBS/AV, PAL/NTSC/SECAM) signals of any video type are supported.
The unparalleled interference rejection and low emissions of the transceiver allows long run video signals to co-exist in the same wire bundle as telephone, data-com, or low-voltage power circuits. This allows the use of shared or existing cable plant. Ground-lifting circuit design ensures no annoying "hum-bars" when ground potential differences exist.
Built-in lightning protection, transient protections, ESD protection, power line contact protection, damaging voltage spike problems are eliminated
Technical Specifications
-
Video Frequency Response:
DC to 6 MHz
-
DC Coupled Amplifier Mode
100V/us transient responding
-
Differential Gain: 0.5%
-
Differential Phase: 0.3°
-
Distance Switch 4-Position Adjustable for each channel.
-
Common-mode/Differential-mode Rejection:
15KHz to 5 MHz, 65 dB typical.
-
Channels Cross Talk: -68dB.
-
Loop Return Loss: over 15dB
-
Figure Enhanced Output:
4.43MHz extra emphasis
-
Line Impedance:
Coax, female BNC 75 ohms, CAT5 line, Terminal Block 100 ohms.
-
Wire Type: Network Wiring One Unshielded Twisted Pair 24-16 AWG (0.5-1.31mm).
Category Type Cat 5 or better. Impedance 100±20 ohms.
-
DC Loop Resistance 52ohms per 1,000 ft (18 ohms per 100m).
-
Differential Capacitance 19pF/ft max (62pF/m max).
-
LED Indicator: Power On Red Indicator LED Light.
-
Power Supply: +12VDC/500mA -UST108R
110/220VAC Power - UST108R-2F
|
Environmental
Temperature -20°C to +65°C.
Humidity (non-condensing) 0 to 95%.
Transient Immunity
6,000 V 1.2µS x 50 µS per ANSI/IEEE 587 C62.41 B3.
3,000 V 8µS x 20 µS when ground screw terminal is bonded to earth-ground.
Equipment Installment
1: Put the video signals you need in the VIDEO IN/OUT of CAT5 Video Transceiver.
2: Put a twisted-pair in the VIDEO A, B screw terminals of CAT5 Video Transmitter and Receiver respectively.
3: Connect with the mains following instructions shown in the system configuration diagram or sketch map, make sure power supply in +12VDC.
4: Set the position of ADJ correctly according to the distance table in Transceiver.
5: 3 ‘GND’ screw terminals are bonded to earth-ground.
6: After the five steps, the 08 VIDEO Outputs of 08 Channel CAT5 Video Receiver/Hub is ready to work.
Check after Connection
1. Power On Red Indicator LED Light.
2. Make sure that UTP wire and coaxial cable is correctly and firmly connected.
3. Make sure the ‘GND’ screw terminal is firmly connected to earth-ground.
Mechanical
Dimensions:326X120X33mm
Material: Metal housing case
Maintenance & Quality Guarantee
3 Year Warranty
|
