pipeline API 5L X70/X70 STEEL PLATE
API 5L standard specification for line pipe
The purpose of this specification is to provide standards for pipe suitable for use in conveying gas, water, and oil in both the oil and natural gas industries.
This specification covers seamless and welded steel line pipe. It includes plain-end, threaded-end, and belled-end pipe, as well as through-the-flowline (TFL) pipe and pipe with ends prepared for use with special couplings
PSL 1API 5L X70 Chemical Composition
The Element Max (%)
Seamless
C 0.28
Ti 0.06
Mn 1.40
P 0.03
S 0.03
Welded
C 0.26
Ti 0.06
Mn 1.65
P 0.03
S 0.03
PSL 1API 5L X70 Mechanical Property
Yield Min Mpa:483
Tensile Mpa:565
Elongation Min %:a
PSL 2API 5L X70 Chemical Composition
The Element Max (%)
Seamless
C 0.24
Ti 0.06
Mn 1.40
P 0.025
S 0.015
Welded
C 0.22
Ti 0.06
Mn 1.65
P 0.025
S 0.015
PSL 2API 5L X70 Mechanical Property
Yield Min Mpa:483-621
Tensile Mpa:565-758
Elongation Min %:a
The minimum elongation in 2 in. (50.8 mm) shall be that determined by the following equation:
U.S.Customary Unit Equation: e= 625,000*A0.2/U0.9; SI Unit Equation: e= 1,944A0.2/U0.9
Where e= minimum elongation in 2 in. (50.8 mm) in percent rounded to the nearest percent.
A= applicable tensile test specimen area, as follows:
For round bar specimens:
-----0.20 in.2 (130 mm2) for the 0.500 in. and 0.350 in. specimens,
-----0.10 in.2 (65 mm2) for the 0.250 in. specimen
b. For full section specimens, the smaller of (i) 0.75 in.2(485 mm2) and (ii) the cross-sectional area of the test specimen, calculated using the specified outside diameter of the pipe and the specified wall thickness of the pipe, rounded to the nearest 0.01 in.2(10 mm2);
c. For strip specimens, the smaller of (i) 0.75 in.2 (485 mm2) and (ii) the cross-sectional area of the test specimen, calculated using the specified width of the test specimen and the specified wall thickness of the pipe, rounded to the nearest 0.01 in.2 (10 mm2).
U = speciÞed minimum ultimate tensile strength in psi (MPa).
API 5L standard specification for line pipe
The purpose of this specification is to provide standards for pipe suitable for use in conveying gas, water, and oil in both the oil and natural gas industries.
This specification covers seamless and welded steel line pipe. It includes plain-end, threaded-end, and belled-end pipe, as well as through-the-flowline (TFL) pipe and pipe with ends prepared for use with special couplings
PSL 1API 5L X70 Chemical Composition
The Element Max (%)
Seamless
C 0.28
Ti 0.06
Mn 1.40
P 0.03
S 0.03
Welded
C 0.26
Ti 0.06
Mn 1.65
P 0.03
S 0.03
PSL 1API 5L X70 Mechanical Property
Yield Min Mpa:483
Tensile Mpa:565
Elongation Min %:a
PSL 2API 5L X70 Chemical Composition
The Element Max (%)
Seamless
C 0.24
Ti 0.06
Mn 1.40
P 0.025
S 0.015
Welded
C 0.22
Ti 0.06
Mn 1.65
P 0.025
S 0.015
PSL 2API 5L X70 Mechanical Property
Yield Min Mpa:483-621
Tensile Mpa:565-758
Elongation Min %:a
The minimum elongation in 2 in. (50.8 mm) shall be that determined by the following equation:
U.S.Customary Unit Equation: e= 625,000*A0.2/U0.9; SI Unit Equation: e= 1,944A0.2/U0.9
Where e= minimum elongation in 2 in. (50.8 mm) in percent rounded to the nearest percent.
A= applicable tensile test specimen area, as follows:
For round bar specimens:
-----0.20 in.2 (130 mm2) for the 0.500 in. and 0.350 in. specimens,
-----0.10 in.2 (65 mm2) for the 0.250 in. specimen
b. For full section specimens, the smaller of (i) 0.75 in.2(485 mm2) and (ii) the cross-sectional area of the test specimen, calculated using the specified outside diameter of the pipe and the specified wall thickness of the pipe, rounded to the nearest 0.01 in.2(10 mm2);
c. For strip specimens, the smaller of (i) 0.75 in.2 (485 mm2) and (ii) the cross-sectional area of the test specimen, calculated using the specified width of the test specimen and the specified wall thickness of the pipe, rounded to the nearest 0.01 in.2 (10 mm2).
U = speciÞed minimum ultimate tensile strength in psi (MPa).
1. Steel Standards: CCS, DNV, GL, LR, BV, KR, ABS, API, RINA, NK, ASTM, GB5313.
2. Steel Grade: A, B, D, E, AH32, AH36, AH40, DH32, DH36, DH40, EH32, EH36, EH40, FH36, FH32, FH40, API 2H Gr42, 2H Gr50, A514Gr (F, Q). API 2H Gr50, API 2W Gr50, API 2W Gr50T, API 2W Gr60, API 2Y Gr60.
3. Steel Specification:
T: 8-650mm, W: 1500-4020mm, L: 3000-27000mm.
4. Delivery Condition: TMCP, Q&T, N, AR, CR, A, Q and N&T
5. Steel Test: UT, HIC, Impact test, PWHT, Z15, Z25, and Z35.
6. Payment Term: T/T, L/C at sight.
7. Trading Term: FOB, CFR, CIF, CNF
8. Delivery Time: 23- 35 days