Type 347 stainless steel has slightly improved corrosion resistance over type 321 stainless steel in strongly oxidizing environments. Type 347 is stabilized with columbium, it is preferable for aqueous and low temperature environments due to its good resistance to intergranular attack. Both 347 and 321 offer good resistance to polythionic acid stress corrosion cracking, encountered in oil refineries. The high temperature oxidation resistance of 347 is similar to that of 304 stainless steel. Useful to 1500°F.
Often in many product forms, the grain size and carbon content can meet both the 347S and 347H requirements. Appropriate weld fillers are AWS ER347 bare wire and E347 covered electrodes.
Common Trade Names
Often in many product forms, the grain size and carbon content can meet both the 347S and 347H requirements. Appropriate weld fillers are AWS ER347 bare wire and E347 covered electrodes.
347H, 347 Stainless
Inventory
347 Sheet, 347 Plate, 347 Bar, 347 Welding Products
Specifications
UNS S34700, UNS S34709, ASTM A 240, AMS 5512, ASME SA240, ASTM A262 Practice E, PWA F17 LCS, PWA 300, MSRR 5632
Chemical Composition, %
| Cr | Ni | Cb + Ta | C | Si | Mn | P | S | Fe | |
|---|---|---|---|---|---|---|---|---|---|
| MIN | 17.0 | 9.0 |
Cb 10xc (Cb 8xC) |
0.04 | - | - | - | - | |
| MAX | 19.0 | 13.0 | 1.0 | 0.08 | 0.75 | 2.0 | 0.045 | 0.03 | Balance |
- Good creep strength up to 1500°F
- Maintains good corrosion resistance in applications where the temperature is between 800°F and 1500°F.
- Good resistance to intergranular corrosion in the as welded condition.
- Oil Refineries
- Fluid catalytic cracking units (FCC)
- Hanger rods
- Recuperator tube sheets, shell, supports
- Especially where temperatures exceed 550°F and resistance to sulfidation is needed
- Fired heater tubes
- Distributor trays and thermowells
- Equipment in and around reactors (good resistance to polythionic acid)
Density: 0.286 lb/inch3
Melting Point: 2550 - 2635°F
Melting Point: 2550 - 2635°F
| Temperature, °F | 70 | 212 | 932 |
| Coefficient* of Thermal Expansion, in/in°F x 10-6 | - | 9.2 | - |
|
Thermal Conductivity Btu • ft/ft2 • hr • °F |
- | 112.5 | 147.7 |
| Modulus of Elasticity, Dynamic psi x 106 | 28 | - | - |
* 70°F to indicated temperature.
Mechanical Properties
Minimum Specified Properties, ASTM A 240
| Tensile Strength, ksi | 75 |
| 0.2% Yield Strength, ksi | 30 |
| Elongation, % | 40 |
| Hardness Max, Brinell | 201 |
Typical Tensile and Impact Properties
| Temperature, °F | 68 | 400 | 800 | 1000 | 1200 | 1350 | 1500 |
| Ultimate Tensile Strength, ksi | 93.3 | 73.6 | 69.5 | 63.5 | 52.3 | 39.3 | 26.4 |
| 0.2% Yield Strength, ksi | 36.5 | 36.6 | 29.7 | 27.4 | 24.5 | 22.8 | 18.6 |
* Above data from Allegheny Ludlum Steel Corporation's Blue Sheet
Bolt: M6-M64 (hexagonal, flange)
Nut: M3-M64 (hexagonal, flange)
Threaded Rod:4-3000mm (all thread, double end thread)