Unpack the HEATED  GLOVES, along with the two Li-Ion Polymer batteries and
adapter.
The batteries of the HEATED GLOVES are not charged and must be fully
charged for 8 hours before first use.
Connect the Y-Cable to the main adapter cable and then the two adapter cables
to the sockets of the batteries. Then plug in the adapter to the outlet to charge the
batteries. Both batteries must always be charged at the same time!
After the initial charge, the regular charging time is approximately up to 8 hours
depending on the charging state of the batteries. The adapter is designed to
protect and guarantee a long life of the batteries. Overcharging is not possible.
The two LED lights on the Y- cable turn to red during loading and then change
to green after loading is completed! After the gloves are fully charged, unplug the
adapter and disconnect the cables from the batteries. Store the batteries in the
pouch inside the cuff of the gloves and close the zipper.
When using your HEATED GLOVES open both zippers of the pouch inside the
gloves and connect the cables, which are inside the pouch, to the sockets of the
battery firmly. Store the battery inside the pouch and close the zipper.
The Heating Mode is activated by pressing the black ON/OFF keypad control
button located on the top of the gloves for about 3 seconds. The LED light on
the keypad control will then flash and light up, indicating that the gloves are in the
Heating Mode.
The initial color of the LED light indicates the present charging status of the battery:
THREE-REDS indicates that the battery is fully charged.
TWO-REDS indicates that the battery is halve charged and
ONE-RED indicates a low battery level and that the battery should be charged before
use!
The temperature can be adjusted by pressing and releasing the keypad control
button.
L – ONE LED (34°C/ 93°F with approximate heating time of 4 – 5 hours)
M - TWO LED (39°C/ 102°F with approximate heating time of 3 – 4 hours)
H - THREE LED (44°C/ 111°F with approximate heating time of up to 2 hours)
Please note that the actual heating time always depends on the outside temperature
and if the gloves are worn separately, or in conjunction with outer gloves or
mittens. The Li-Ion batteries reach its full power after having been fully charged and
fully drained several times! Additional batteries packs can be purchased separately
if extended heating times are needed!
Turn OFF the gloves by pressing the ON/OFF keypad control button several
seconds until the LED light turns off. Always unplug the batteries when the gloves
HEATED GLOVE LINER INSTRUCTIONS
are not in use and store them inside the pouch of the glove.
The high-quality 2800 mAh Li-Ion Polymer Batteries (no memory effect!) cannot
be damaged by frequent charging and can be re-charged approximately 500 times!
STORAGE:
For best performance it is recommended not to fully charge the batteries if the
gloves are not being used for a longer period of time! Charge for 30 minutes only
and after 3 months charge the batteries again for about 30 minutes!
Charge the batteries completely before using the gloves again.
CARE INSTRUCTIONS:
•• Turn OFF the gloves when not in use.
•• Always unplug the batteries when the gloves are not in use and store them
inside the pouch of the glove.
•• Store the gloves and adapter in a cool, clean and dry place.
•• Only use the original adapter to charge the gloves.
•• Do not damage the heating elements by excessively stretching
or twisting the gloves.
•• Do not cut or puncture the gloves.
•• The temperatures were measured directly at the carbon fiber material.
•• Do not dry clean.
•• Do not iron.
The indicated temperatures are measured directly at the carbon fiber close to the
battery.
WASHING INSTRUCTIONS:
•• Hand wash only! Please use a mild detergent and treat the gloves carefully.
•• Air-dry the gloves only! Do not place them on radiators or any other hot surface!
•• Let the gloves dry completely before charging again.
HELPFUL INFORMATION:
Please perform the following test in case you feel that the gloves are not heating
correctly:
–– Charge the gloves completely.
–– Now turn ON the gloves by pressing the ON/OFF keypad control button about 3
seconds until the LED light turns on!
–– Place the gloves in the refrigerator for 5 – 10 minutes.
–– Check the LED light of both gloves after taking them out of the refrigerator again.
–– If the light is ON, then the gloves are in the heating mode and you should feel
the warmth on the fingers and also the upper side of the gloves after about one
minute.
DISCARDING OF THE GLOVES:
Discard HEATED GLOVES with approved collection agencies only! In order to
save our environment, do not dispose the gloves in your normal household trash.
Discard the batteries separately from the gloves!