Fly Ash Block Making Machine
1.use widely
2.high efficient
1.use widely
2.high efficient
fly ash block making machine
We are most professional manufacturer of autoclaved aerated concrete (AAC) plants for more than 12 years, and we can supply complete set of autoclaved aerated concrete plant with 50 000m3, 100 000m3, 150 000m3, 200 000m3, 250 000m3, 300 000m3 capacity annually, including plant design, equipments installation, technical instruction, personal training, etc, and also can design and manufacture as per clients' requirement.
Raw materials: cement, lime, sand, gypsum, aluminium powder, water
Equipment list:
The equipment will be divided into two parts: specialized equipment and universal equipment.
Other relative equipments as follows:
1. Cutting machine.
2. Tilting hanger, mould, side plate, hardening cart, mould frame, mould bottom, casting machine, hoist
3. autoclave, horizontal installation stem boiler
Whole production procession:
The aerocrete produces the technological process:
1. The raw materials store in the material storehouse (or stores the pot) after dealing with reserve such as lime, cement, gypsum, sand (or fly ash)
2. Aluminium powder or aluminium lotion is through dealing with the reseve material for use
3. Raw materials measure according to certain matching by electron balance measure, aluminum powder, water put into aluminum mixer. it is suspends the liquid to make the mixture after measuring.
4. The batching water (cold water or hot water pitcher hot water) is measured by the electronic water balance.
5. Put into and pour among the mixers in certain order after, raw materails, aluminum powder suspend the liquid is measured, pour and enter the mould after mixing evenly (panel should be put network slice of reinforcing bar in advance in the mould)
6. Quiet to is it raise in advance to park through certain temperature and time, is it transport to the cutting machine to hang from upset hoist upset 90 degree after the base body reaches certain intensity, the drawiang of patterns is cut
a. The base body carries on the side and cuts and mills through vertically at first
b. Then carry on the verrtical level to cut
c. Cut horizontally finally
d. Cut good base body raises to cauldron car go on one yeard of shelves organize into groups to steam to transport to hang to drive a vehicle to load
7. Raise products well, produce after the cauldron breaking the board off the fingers and thumb by the board breaking off the fingers and thumb machine to steam
8. Pile from finished product hoist or forklift to finished product field pile the buttess according to specification to carry
9. Steaming and raising the car and side board and entering the next board of circulation and returning after, the finished product is unloaded, with upset hoist mould frame association the drawing of patterns get off, restore 90 degrss return to pour mixer pour again after clearing up.
Raw materials: cement, lime, sand, gypsum, aluminium powder, water
Equipment list:
The equipment will be divided into two parts: specialized equipment and universal equipment.
Other relative equipments as follows:
1. Cutting machine.
2. Tilting hanger, mould, side plate, hardening cart, mould frame, mould bottom, casting machine, hoist
3. autoclave, horizontal installation stem boiler
Whole production procession:
The aerocrete produces the technological process:
1. The raw materials store in the material storehouse (or stores the pot) after dealing with reserve such as lime, cement, gypsum, sand (or fly ash)
2. Aluminium powder or aluminium lotion is through dealing with the reseve material for use
3. Raw materials measure according to certain matching by electron balance measure, aluminum powder, water put into aluminum mixer. it is suspends the liquid to make the mixture after measuring.
4. The batching water (cold water or hot water pitcher hot water) is measured by the electronic water balance.
5. Put into and pour among the mixers in certain order after, raw materails, aluminum powder suspend the liquid is measured, pour and enter the mould after mixing evenly (panel should be put network slice of reinforcing bar in advance in the mould)
6. Quiet to is it raise in advance to park through certain temperature and time, is it transport to the cutting machine to hang from upset hoist upset 90 degree after the base body reaches certain intensity, the drawiang of patterns is cut
a. The base body carries on the side and cuts and mills through vertically at first
b. Then carry on the verrtical level to cut
c. Cut horizontally finally
d. Cut good base body raises to cauldron car go on one yeard of shelves organize into groups to steam to transport to hang to drive a vehicle to load
7. Raise products well, produce after the cauldron breaking the board off the fingers and thumb by the board breaking off the fingers and thumb machine to steam
8. Pile from finished product hoist or forklift to finished product field pile the buttess according to specification to carry
9. Steaming and raising the car and side board and entering the next board of circulation and returning after, the finished product is unloaded, with upset hoist mould frame association the drawing of patterns get off, restore 90 degrss return to pour mixer pour again after clearing up.
Specialized equipment includes:
1. Cutting equipment: tilting crane, cutter.
2. Proportioning equipment: elecronic measuring scle, slurry beating machine, slurry storage tank, slurry mixer.
3. Pouring and autoclave equipments: aluminum powder mixer, pouring mixer, mould, side plate, autoclave truck, carrier car.
4. Enviornment protect equipments: dust remover.