| Name: | DVN Pneumatic valve |
|
DVN SERIER Low Pressure Pneumatic Diaphragm Valve Specifications • Reduced inner capacity • Electropolished , D.I. water cleaned , assembled ,tested and packaged in certified clean room. • Minimal contributions of Moisture, Oxygen and Hydrocarbon. • Permanently heat code laser marked; Material traceable to original mill certificate of test. • Hastelloy®C-22™ and custom configurations available upon request. |
|
DVN Series: pneumatic valve; diaphragm valves; gas flow meter; manual valve; dual actuator valve
ow Pressure Pneumatic Diaphragm Valve
Specifications
• Reduced inner capacity
• Electropolished , D.I. water cleaned , assembled ,tested and packaged in certified clean room.
• Minimal contributions of Moisture, Oxygen and Hydrocarbon.
• Permanently heat code laser marked; Material traceable to original mill certificate of test.
• Hastelloy®C-22™ and custom configurations available upon request.
| Size | 1/4" | 3/8",1/2" | 3/4" |
| Cv Value | 0.3 | 0.7 | -0.7 |
| Orifice Size | 4.5mm | 7.8mm | 7.8mm |
| Max. Working Pressure(G.) | 1Mpa | ||
| Operating Pressure(G.) | 0.4~0.7Mpa | ||
| Max.Working Temp. | PCTFE:-10℃~65℃/PFA:-10℃~120℃/PI:-10℃~150℃ | ||
| Internal Leakage Allowance(He) | 1x10-10Pa.M3/S | ||
| Test Pressure ≦1x10-2Torr | |||
| Holding Time ≧15 sec | |||
| External Leakage Allowance(He) | 1x10-10Pa.M3/S | ||
| Test Pressure ≦1x10-2Torr | |||
| Holding Time ≧1 min | |||
| Particle Inspection(EP only) | No count | ||
| Pressure:60~80psi N2 Gas | |||
| Sample Volume:1CMF | |||
| 0.1μm and Larger | |||
| Product Grade | AP | BA | EP |
| Inner | Ry≦25μm | Ry≦25μm | Ry≦25μm |
| 10μinch RA(Avg.) | 5μinch RA(Avg.) | ||
| Surface | Cut off length:2.5mm | Cut off length:0.8mm | Cut off length:0.25mm |
| Roughness | Measuring Length:12.5mm | Measuring Length:4mm | Measuring Length:1.25mm |
| Polishing | Machining Finish | Machining Finish | Electro Polishing Finish |
| Order Information | |||||||||||
| DVN | Code | Material Type | |||||||||
|
|
S | SUS316L Single Melt(Standard Type) | |||||||||
| D | SUS316L Double Melt | ||||||||||
| 4S | SUS304 | ||||||||||
|
|
Code | Size Type | |||||||||
| 4 | 1/4"(Standard Type) | ||||||||||
| 6 | 3/8" | ||||||||||
| 8 | 1/2" | ||||||||||
|
3/4" | ||||||||||
| Code | Connection Type | ||||||||||
| SW | Lok(Standard Type) | ||||||||||
| VM | MFS Male | ||||||||||
| VF | MFS Female | ||||||||||
| TW | Butt Weld | ||||||||||
|
|
Code | Operation Method Type | |||||||||
| C | Normally Close(Standard Type) | ||||||||||
| O | Normally Open | ||||||||||
|
|
Code | Option | |||||||||
| x47 | Constant Bleed φ0.3(Standard Type) | ||||||||||
| x59 | Constant Bleed φ0.6 | ||||||||||
|
|
Code | Grade Type | |||||||||
| B | BA Grade | ||||||||||
| P | EP Grade | ||||||||||
| A | AP Grade | ||||||||||
|
|
Code | Logo | |||||||||
| F | FGT Logo(Standard Type) | ||||||||||
| C | Customer Logo | ||||||||||
|
|
|||||||||||
| DVN | Complete Ordering Code | ||||||||||
| ＊Note:Using customer Logo launch to more than 1000 united for one year | |||||||||||