Heavy Duty 6-24Vdc Micro DC Submersible Pump, brushless, Max Head 8m, Low Noise, ultra-quiet, Waterproof, Power Saving
Amphibious, land use or diving
Mute (Ultra Low Noise)
Surprisingly Powerful in so small size
Power Saving with just 42W with 24Vdc Voltage
Can be used for High Temperature fluids pumping when land use
This pump product, with ceramic shaft and ceramic sleeve, more muted. The consecutive life expectancy of can be over 30,000 hours. Amphibious use(Soaking or not). Non-self-priming, water should be able actively flow into inlet of pump at land use connecting with outside pipe. Long time work without fluids inside pump can be damagable.
Typical features:
Operating voltage :6-24V (voltage more than 24V is not advised), current 720mA at 24Vdc, Max static head 8 meters, Max horizontal flow 1200L / H. (Ultra power saving)
Materials: Pump body with high-temperature-proof plastic material. The sleeve and shaft with high-strength ceramics. (Note: usually common pump only with the ceramic shaft, without ceramic sleeve)
Structure: with four suction cups on the bottom, can be arbitrarily fixed on a smooth surface.
Power cord: diameter 3.0MM waterproof round wire length of 2 meters and waterproof connector.
Product size: 74 * 41 * 51 (H) MM (including water inlet and outlet)
Pump outlet diameter: OD 11MM
Pump inlet diameter: OD 13MM
Suitable medium: water, oil, and other acid-base solution. (Land use when pumping acidic liquids, submersible installation is not advised at this case)
Max Operating Temperature: resistance to high temperature of 100 degrees. Pumps can dive at room temperature, land use (not soaking) at high temperature(>75C). (Pump body material itself can be resistant to 200 degree Celsuis)
Useages: Pump can be widely used inefrigeration system, water circulation system, the solar collector circulation system, the solar temperature circulation system, hot water pipe circulation system (to get instant hot water when opening), solar water-warming mattress, floor heating, fountains, etc.
For Wire, Brown is Positive, Blue is Negative.
Parameters (Can be customized for bulk demands)
1. Make sure the working voltage, current, head and flow. The Max head means the static head. The pump can lift to the max heightwhen there is no flow. If you want special flow at special height, you must choose more higher head than the height you want to pump.
2. Make sure the dimension(threaded interface or not, the direction and diameter of outlet and inlet).
3. Working environment(temperature and medium).
4. Other functional requirements, such as time control, motion control, pressure control, flow control, and speed adjustment.
NOTE when using:
1 Work at over-voltage is forbidden. Voltage can be highly more than rated voltage for Battery with more than 10AH at full capacity when there is no voltage-limitation measure. Pls test the supply voltage before working if you are not sure about it. Specification of Source Adapter is advised at 24Vdc, more than 3A.
2 No direct AC Power supply.
3 About the Max static head. Pump with 3.2m head doesn't mean that it can spray as high as 3.2m when connecting with power supply. The real mean of head is that the vertical height of the water column in the plumbing. Spray head is much lower than head.
4 Regulated power supply and switching power supply are advised for more than 2A for a certain margin.
5 Pump is not allowed to disassembly unauthorized. Ceramic shaft and sleeve are precisely installed and it's difficult for non-professionals to reassembly. We are not responsible for quality problems caused by this.
6 Ferromagnetic impurity and particles should not be in pump for they affect magnetic actuator and bearing friction. Pump should be promptly cleaned when transporting media that is easy to crystallize or precipitate( Clean operation: pumping clean water for 1min). Pls filter articles before inlet when pumping fluids with solid particles.
Typical technical features:
1 Brushless design, with the electronic component commutation, no friction loss and high temperature caused by brush friction.
2 High-performance and wear-resistant ceramic shaft and ceramic sleeve. Sleeve and magnet have been combined together through plastic injection. Long life span without friction, as long as more than 10yrs without maintence.
3 Stator and rotor are completely isolated from each other, while stator and circuit board are potted by epoxy. 100% waterproof and Amphibious use.
4 Rotor part with permanent magnet, pump body with eco-friendly materials. Low noise(always lower than 35dB), micro size, high efficiency and power saving.
5 Pump parameters can be adjusted by stator winding, eg. the max head of 12V pump can be from 1m to 5m, etc. Quite working voltage range.
6 Four suction cups in pump base. They can also be removed as you wish.