Pühler SupermaxFlow1000? Horizontal Disk Mill is specially designed for mass production such as titanium dioxide grinding. The mill is very solid built to offer a superior performance with minimum maintenance and operation cost.  

Pühler SupermaxFlow1000? Horizontal Disk Mill Simplicity in Maintenance

 

horizontal layout for simple mill access

The most crucial part of any mill maintenance is access. Unlike conventional mills where maintenance is done inside the mill with the PUHLER SupermaxFlow1000? Mill the shell is removed from the mill internals making access easier and shutdowns faster. The PUHLER SupermaxFlow1000? Mill grinding chamber and discharge end are fixed to trolleys that sit on rails. Hydraulic rams move the grinding chamber along the support rails and expose the internal components of the mill for maintenance.

 

The advantages of the PUHLER SupermaxFlow1000? Milll horizontal configuration include simple overhead (or mobile) crane requirements and simple media handling. Media can be dropped into the integrated media hopper and is retrieved and returned to the PUHLER SupermaxFlow1000? Mil via the Super Canister Separation System( SCS ) media handling system

 

easy start up after stops

Unlike alternative technologies the horizontal, 8 disc layout of the PUHLER SupermaxFlow1000? Mil means it starts easily even after being crash stopped at full load – all 8 discs are available to achieve breakaway torque through the settled media load.

 

the internal wear components

Over the last decade over 20 different types of wear materials have been tested in the PUHLER SupermaxFlow1000? Mil to determine the characteristics that components need for long wear life.

 

Feed and Discharge end flanges – replaceable rubber wear component that slide onto the steel surfaces and then are bolted in place.

 

Grinding Chamber (shell) – PUHLER SupermaxFlow1000? Mil are designed with a split shell in which a replaceable slip-in liner can be installed. The PUHLER SupermaxFlow1000? Mil shell can be unbolted, opened into two halves and the worn shell slip-in liner removed and a new one installed. There is no need to send the shell away for relining and have a spare shell on site.

 

Grinding Disks – consist of 2 components a relatively cheap disposable disc and a more expensive reusable hub that connects the disk to the mill shaft. All wear components are steel backed with rubber or similar coating. They are fabricated off-site then stored on-site until required. The components are relatively low cost, light and easy to handle and store while still providing long wear lives.

 

shaft sealing system

The shaft sealing system prevents slurry and grinding media discharging from the point where the rotating shaft enters the grinding chamber. The gland seal packing is comparable to that used in slurry pumps and with consistant, good quality water supply can be expected to have a life of at least 6 months.

 

maintenance program

Maintenance of the PUHLER SupermaxFlow1000? Mill is as simple as routine maintenance for a slurry pump. The internal rotating shaft is counter-levered at the feed inlet end so the discharge end flange and grinding chamber can be simply unbolted and slid off (using hydraulic rams).

 

The grinding discs can be removed by undoing the locking nuts at the end of the shaft. The old discs are slid off and new discs slid on. The bolt-on wear components and shell liner can then be replaced (if required) before the shell is slid back into position and bolted up… the PUHLER SupermaxFlow1000? Milll is ready to run. Typical SupermaxFlow1000? Mill shutdowns last 6-10 hrs

 

The maintenance schedule is built around the grinding discs, all other components last several cycles of disc replacement. Continuous improvement of all components have seen an increase in wear life and a drop in downtime and maintenance costs.

 

PUHLER SupermaxFlow1000? Mill component life is dependant on the application however grinding discs generally last up to 6 months and shell liners can last up to 1 year. Typically PUHLER SupermaxFlow1000? Mil maintenance takes 6-12 hours and is cheduled into routine planned shutdowns. With maintenance occurring every 6-8 weeks availability exceeds 97%.