1, all gear drive transmission, advanced technical performance, long life,
 
 
2, fast, slow and reverse speed parameter set reasonable,
 
 
3, all using the world's most advanced air-cooled, direct injection, vertical diesel engine as power, which is characterized by

A fuel-efficient, convenient, and reliable quality. Compared with the cost of gasoline can save 30 yuan per mu.
 
 
4, moderate in general about the whole weight 100KG, its cultivation effect, high efficiency, the scope of application

Wai Kwong.
 
5, in the hard, small plots, shallow water fields, blisters Tin geographical operations have greater advantages to solve the hand
Farm tractor not a problem.
 
6, easy to transport, time-saving, high fuel efficiency, without water, the body is not easy to cold and so on.

Running in

1, before the break-in

In order to prolong the service life of micro tillage machine, new machine before use, be sure to try first to get up to speed. Tighten connection micro tillage machine components, add sufficient combustion

Oil, lubricating oil and water, check and adjust the v belt tension. Check the tire pressure, check the working condition of the handle.

2, in basic principles

From low to high speed, load from small to large

3, the purpose of the break-in

In good technical conditions and the conditions of lubricating oil is as follows, by slowly increasing load, ground to the surface of the parts with uneven parts gradually, for micro tillage machine

The normal use and prolong service life lay the foundation.

4, break-in matters needing attention

(1) in braking and steering test for many times, must be conducted and check the operating mechanism is working correctly.

(2) after the break-in, to strike off the bottom of the pan and diesel engine oil. Cleaning the oil pan and parts in the lubricating oil system, clean the filter

Qing wares, and then add new oil, add right amount diesel, chassis empty low driving a few minutes to wash and iron filings to remove grinding down.

(3) check the nut and screw down the cylinder head and other nuts, screws.

(4) check and adjust the valve clearance, a free travel of clutch and brake.

(5) after overhaul of walking micro tillage machine should also to get up to speed, running-in specifications stipulated by half.

(2) the use and operation

Use of preparation and initiation before, according to the requirements of the instructions, check the oil, diesel oil, cooling water and gearbox lubricant.

1, check the tire pressure is in line with the requirements.

2, check whether the main parts of bolt fastening (focusing on frame, drawing frame and the gearbox housing, driving wheel and other parts of the connection bolt).

3, the clutch handle in the "off" position, the gear lever in the neutral position, the throttle lever in "start" position, the throttle switch on:

"On" position.

4, decompression, machine-cleaned pulled, started in the engine specification of diesel engine.

5, to start

(1) check whether the left and right steering gear is reliable joint (inspection methods: don't hold to hand, swinging arm, when micro tillage machine can't turn

, said gritting steering wheel sets have joint)

(2) diesel engine starts, the separation of the clutch, shift lever under the required gear.

(3) step on the gas can also use the small throttle (no load), hands loosen clutch slowly and steadily, to the position of "close",

Micro tillage machine is started.

(4) when the clutch is connected to slow, began immediately after the combination, reduce the clutch slippage and the wear and tear.

7, the choice of gear and transformation

(1) in the field of micro tillage machine farming, choose at most I and II archives work, otherwise will cause overload, which affects the service life of micro tillage machine.

(2) the need to transform top micro tillage machine work, must first to separate the clutch, then shift lever, gear needed to hang.

(3) by the low gear transform top, should first step on the gas increase speed after shift, by high gear with low gears, should reduce the accelerator

Reduce speed again after the shift, such not only drive steady, and avoid damage to the gear.

8, steering

3 (1) reduce the throttle

(2) in flat road and slope, the smaller the left hand, micro tillage machine on the left: pull the right hand, micro tillage machine to the right.

(3) under a steep slope, to operate the opposite. Namely, the left hand, micro tillage machine turn right: the right hand, micro tillage machine on the left.

9, backward

Hands to clutch the 15 in the "off" position, the gear lever in reverse 16 position, then slowly steady hands put down the clutch to "close"

The location of both can make the micro tillage machine back. At this point is easy to use small throttle.

10, parking and brake

(1) parking will clutch system handle in the "off" position, the gear lever in high-grade position, gradually decreasing throttle 3, parking can be implemented. stop

After car clutch brake handle 15 back on the "close" position, the winter long time parking must be put to the best of cooling water, outdoor storage, to cover the exhaust pipe,

In case of rain water; Summer noon to cover the triangle, in case of thermal deformation and aging.

(2) the micro tillage machine not parking stall, clutch brake lever handle 15 on "brake" position.

(3) brake single brake, turn down the gas. 3, quickly put on the clutch brake lever handle 15 "brake" position; With trailer, should be used

Trailer brake, it is forbidden to use chassis of the brake. Generally don't stop on the ramp, must stop at the ramp, should be shut down

Files, tire underlaying triangular wood.

12, using a commonly, but in row weeding work load is lighter and paddy field a second rotary cultivator work can use the second gear, and productivity

High. Homework, don't make the weeds on the coulter around too much, otherwise will increase micro tillage machine power consumption and parts of wear and tear, weeds need to turn down

The gas pedal. The clutch handle in the "off" position, and screw rotary tillage separation claw, is in a state of separation, and then use the hook to pull weeds.