Detailed introduction to misting system KF2802C:

Misting system KF-2802C 

Model 3wa-1150 
Power 200w 
Flow rate 1l/min 
Pressure 80bar 1150psi 
Pump type 3wa-1150 
Rpm 1400r/min 
Power require electric voltage: 220v 
Dimension 43 x 22 x 29cm 
G. W.: 11kgs 

Accessories: 
15m high pressure hose 
13 nozzles 

Advantage: 
1)Stop working automaticaly when lack of water 
2)Fog can Spray with different frequencies 
3)Controlled by the Timer 

Feature: 
1)Forged brass manidold 
2)NSK bearing 
3)Italy seal 
4)First-grade ceramic plunger 
5)Stainless steel cover 
6)With digital timer, operating easily 

Application: 
(1) Stockbreeding: Deodorization, disinfection, cooling 
(2) Diggings and painting area: Cooling, dust-catching, static-elimination 
(3) Greenhouse, wine-cellar: Cooling and wetting 
(4) Spinning industry: Wetting, static-elimination 
(5) Outdoor plaza, sports, open coffee, beer bars: Sight, cooling, mosquito-killing 
(6) Kursaal, park, restaurant: Sight, cooling, mosquito-killing 
(7) School, factory and warehouse: Cooling 

How to Install an Outdoor Misting System 

Step 1 
Cut PE pipe into lengths of 24 inches. Use a PE pipe cutter to cut the pipe, as this is easier and will not leave debris in the pipe. Coat the pipe and nozzle with PE primer. The nozzle is a PE joint with a spray nozzle head. Coat about 0.5-inch of the outside of the end of the pipe and the insides of both ends of the nozzle with the primer. 

Step 2 
Glue the nozzles onto the pipe. Use PE glue to coat the end of the PE pipe. Insert the misting nozzle over the pipe. Give a quarter turn to lock into place. Continue priming and gluing the other nozzles and pipes for the straight run of the misting system. The nozzles must line up straight with each other as they are glued to the pipe, as they cannot be adjusted once the glue has dried. Lay the pipe out on the floor of the patio as each straight run is completed. Remove all the spray nozzle heads to allow the system to be flushed. 

Step 3 
Attach the pipe clips to the pipe straight run. Hold the straight run of PE pipe up to the roof of the patio. Hammer the pipe clips loosely onto the roof of the patio. Use three to four clips along the straight run to start. Be sure that the starting clip is an inch higher than the ending clip; This will allow for draining the pipe when necessary. Loosely attach the other straight runs to the patio roof using clips. 

Step 4 
Adjust the nozzle holes so they do not point directly down. The nozzles should tilt out slightly. Using primed elbow fittings, glue the runs together. Be mindful that the nozzles stay at the correct angle; Adjust if necessary. Tighten the clips. Add additional clips between each nozzle. 

Step 5 
Add a drain to the system so that the system can be drained when necessary, especially before winter so the pipes don't freeze and crack. Take a primed elbow fitting and glue to a short piece of pipe, approximately six to eight inches. Attach a drain to the bottom of the pipe. The drain should be able to be unscrewed to release the water. Glue the elbow to the low end of the system. 

Step 6 
Add the water source. Run PE down from the ceiling to the faucet, using elbow fittings when necessary. Screw in an adapter to the faucet. Use an elbow fitting to glue the PE pipe to the adapter. Allow one hour for the glue to set over the entire system. 

Step 7 
Open the drain to begin flushing the system. Turn the water on and allow it to run for several minutes. Turn the water off and attach the spray nozzle heads to the nozzles. Close the drain. The outdoor misting