IC693ALG442 Analog Combination I/O Module Analog Current/Voltage Combination Module 4 Input/2 Output Channels  

IC693ALG442 Analog Combination I/O Module Analog Current/Voltage Combination Module 4 Input/2 Output Channels - IC693ALG442 The Analog Current/Voltage Combination Input/Output module provides up to 4 differential input current or voltage channels and 2 single-ended output channels with either current loop outputs or voltage outputs. Each channel can be individually configured for the current or voltage range, as applicable, required for your application. All module configuration is done through software, except for a jumper required for selecting the current input mode. All ranges can be configured using either the Logicmaster 90-30/20/Micro programming software configurator function or the Series 90-30 Hand-Held Programmer. Note that in this module s description, the module will be simply referred to as the Analog Combo Module. Each analog input is capable of providing five input ranges (two voltage and three current), which are: 0 to +10 volts (unipolar) - default range for both input and output channels. 10 to +10 volts (bipolar) 0 to 20 mA 4 to 20 mA 4 to 20 mA Enhanced The default input range is voltage mode 0 to +10 volts (unipolar) with user data scaled so that 0V corresponds to a count of 0 and 10V corresponds to a count of 32767. Each analog output is capable of providing four output ranges (two voltage and two current): 0 to +10 volts (unipolar) - default range for both input and output channels. 10 to +10 volts (bipolar) 0 to 20 milliamps 4 to 20 milliamps Each output channel is capable of converting 15 to 16 bits (depending on the range selected) of binary (digital) data to an analog output for use as required by your application. User data in 12 12-2 Series 90 30 PLC I/O Module Specifications July 2000 GFK 0898F the%AI and %AQ registers is in a 16-bit 2 s complement format. In current modes, an open-wire fault is reported to the CPU for each channel. The module can go to a known last state when system power is interrupted. As long as user power is applied to the module, each output will maintain its last value, or reset to the low end of the scale (range), as determined by how you have configured the module. Each output channel can be configured to operate in ramp mode using ladder logic. In ramp mode, changes in %AQ data cause the corresponding output channel to ramp to the new %AQ value. The ramp output consists of steps taken each millisecond until the final value is reached. High and low alarm limits can be set for all input channels and an open-wire fault (current output modes) is reported to the CPU for each output channel. All six analog channels may be updated on every scan, depending on the scan time. Table 12-1. Specifications for IC693ALG442 Analog Output Specifications Number of Output Channels 2, Single-Ended Update Rate 4 milliseconds (approximate - both channels) Analog Current Output Output Current Ranges 0 to 20 mA 4 to 20 mA Resolution 0 to 20 mA 0.625 A (1 LSB = 0.625 A) 4 to 20 mA 0.5 A (1 LSB = 0.5 A) Absolute Accuracy1 All Current Modes 0.1% of full scale @25 C (77 F), typical 0.25% of full scale @25 C (77 F), (maximum) 0.5% of full scale over operating temperature range (maximum) Maximum Compliance Voltage VUSER 3V (minimum) to VUSER (maximum) User Load 0 to 850 (minimum) at VUSER =20V, maximum 1350 at VUSER =30V Output Load Capacitance 2000 pF (maximum) Output Load Inductance 1 H (maximum) Analog Voltage Output Output Ranges 10 to +10V (bipolar) 0 to +10V (unipolar) Resolution 10 to +10V 0.3125 mV (1 LSB = 0.3125 mV) 0 to +10V 0.3125 mV (1 LSB = 0.3125 mV) Absolute Accuracy2 Both Voltage Modes 0.25% of full scale @25 C (77 F), typical 0.5% of full scale @25 C (77 F), (maximum) 1.0% of full scale over operating temperature range (maximum) Output Loading 5 mA (2K ohms minimum resistance) Output Load Capacitance 1 F (maximum capacitance) Analog Input Specifications Number of Input Channels 4, differential Update Rate 8 milliseconds (approximate for all 4 channels) Analog Current Input 12 IC693ALG442 Analog Combination I/O Module GFK 0898F Chapter12 IC693ALG442 Analog Combination I/O Module 12-3 Input Ranges 0 to 20 mA 4 to 20 mA 4 to 20 mA Enhanced (Table continued on next page) (Continued from previous page) Resolution 0 to 20 mA 5 A (1 LSB = 5 A) 4 to 20 mA 5 A (1 LSB = 5 A) 4 to 20 mA Enhanced 5 A (1 LSB = 5 A) Absolute Accuracy3 All Current Modes 0.25% of full scale @25 C (77 F) 0.5% of full scale over specified operating temperature range Linearity <1 LSB Common Mode Voltage 200V (maximum) Common Mode Rejection >70 db at DC; >70 db at 60 Hz Cross Channel Rejection >80 db from DC to 1 kHz Input Impedance 250 Input Filter Response 29 Hz Analog Voltage Input Input Ranges 0 to +10V (unipolar) 10 to +10V (bipolar) Resolution 0 to +10V 2.5 mV (1 LSB = 2.5 mV) 10 to +10V 5 mV (1 LSB = 5 mV) Absolute Accuracy3 Both Voltage Ranges 0.25% of full scale @25 C (77 F) 0.5% of full scale over specified operating temperature range Linearity <1 LSB Common Mode Voltage 200V (maximum) Common Mode Rejection >70 db at DC; >70 db at 60 Hz Cross Channel Rejection >80 db from DC to 1 kHz Input Impedance 800K (typical) Input Filter Response 29 Hz Power Requirements External Supply Voltage Range 20 to 30 VDC (24 VDC typical) Power Supply Rejection Ratio (PSRR)4 Current Voltage 5 A/V (typical), 10 A/V (maximum) 25 mV/V (typical), 50mV/V (maximum) Voltage Ripple 10% Current Consumption From Internal +5V Supply 95 mA From External User Supply 129 mA 1In the presence of severe RF interference (IEC 801-3, 10V/m), accuracy may be degraded to 1% FS. 2In the presence of severe RF interference (IEC 801-3, 10V/m), accuracy may be degraded to 4% FS. 3In the presence of severe RF interference (IEC 801-3, 10V/m), accuracy may be degraded to 2% FS. 4PSSR is measured by varying VUSER from 24V to 30V. Refer to Appendix B for product standards and general specifications.

Why do you choose us?

1. 100% original package product, 100% quality assurance. 

If you find a fake product. Please contact us without hesitation! We afford the shipment cost! We send you a new product asking zero cent!

 2. Varied payment methods.

 We adopt Paypal, T/T, and other methods. If you can not trust us , you can choose to pay it via Ali-express! 100% make your money safe!

Wuhan Xieyuan Automation Equipment Co., Ltd

  Choose us, you will not be regret, that is a deal!!!

We supply Original Yokogawa differential pressure transmitters, EJX-A and EJA-A series products. And accept TT/ Paypal /Aliexpress / Western Union payment method. Long time and stable cooperation with Yokogawa company. Choose us, you will not be regret, that is a promise! models EJX110A , EJX115, EJX118A, EJX120A, EJX130A, EJX210A, EJX310A, EJA430A, EJX438A, EJX440A, EJX510A, EJX530A, EJX610A, EJX630A, EJX910A, EJX930A.