Before The Curing

Performance Indicators	A	B
Appearance	Gray Fluid	White Fluid
Viscosity	1500~2500(cps)	1500~2500(cps)
A:B	1:1
Mixed Viscosity	1500~2500(cps)
Operable Time	30~120(min) (Adjustable)
Curing Time	3~5(h)

After The Curing 

Hardness	40~50(Shore A)
Dielectric Strength	≥20(kV/mm)
Dielectric Constant	3.12(1.2MHz)
Thermal Conductivity	≥0.6[W/m.k]
Volume Resistivity	≥1.0×1014(Ω·cm)
Specific Gravity	1.56±0.02(g/cm3)
Flammability Rating	UL94 V-0

   ?20kg/set(A10kg+B10kg), packaging with bucket.    

INSTRUCTIONS

Preparing: Stir completely A and B in each container,  
Mixing:A and B should be fully mixed according to the weighting ratio. Add B to A. Stirring(stir the glue dedicated blade) and mixing. Note that: should be mixedthoroughly when mixing the wall rubber of container into the plastic material. 
De-airing: after mixing which should vacuum degassing for 1-3 minutes. 
Potting: The mixture should be poured into the product as soon as possible, in order to avoid thickening and resulting in poor fluidity. 

Curing: Heat curing or at room temperature curing. The higher the temperature, the quicker curing . The temperature is low, the curing time will be extended either. In winter, it will take a long time to cure, so suggest that heating curing. It is cured for 15 minutes at 80 ° C ~ 100 ° C, about 12 hours at room temperature.

 

MATTERS NEEDING ATTENTION

NOTE

 

1,The mixture should be sealed and stored in a dry environment at room temperature, and should be used as soon as possible, to avoid wastage.

2,The product don't belong to dangerous goods, but avoid contacting skin and eyes.

3,The product is non-toxic, has good physical inertia without stimulation and harm. The product does not contain flammable and explosive ingredients which will not cause fire or explosion without special requirement for transport.

4,Stored for a period of time, the plastic may be layered. So please stir well before using, and can't affect its performance.

5,The following substances may hinder the curing or cause the phenomenon of not cure, so it is used after simple experiments, and need to clean the site of application if necessary.

      A, incompletely cured condensation type silicone rubber.

      B.amine (amine) curable epoxy resin.

      C. ash welding (solder-flux).

 

SPECIFICATION TRANSPORT

PACKAGING

 

1,20kg/set(A10kg+B10kg), packaging with bucket.

2,1 year shelf life if stored below 25 ℃, when the product passed its expiration date, it should be confirmed without abnormal phenomenon, then that can be used.

3,These products don't belong to dangerous goods, so they can be transported as normal chemicals. But be careful of leakage.

INSTRUCTIONS

Preparing: Stir completely A and B in each container,  
Mixing:A and B should be fully mixed according to the weighting ratio. Add B to A. Stirring(stir the glue dedicated blade) and mixing. Note that: should be mixedthoroughly when mixing the wall rubber of container into the plastic material. 
De-airing: after mixing which should vacuum degassing for 1-3 minutes. 
Potting: The mixture should be poured into the product as soon as possible, in order to avoid thickening and resulting in poor fluidity. 

Curing: Heat curing or at room temperature curing. The higher the temperature, the quicker curing . The temperature is low, the curing time will be extended either. In winter, it will take a long time to cure, so suggest that heating curing. It is cured for 15 minutes at 80 ° C ~ 100 ° C, about 12 hours at room temperature.

 

MATTERS NEEDING ATTENTION

NOTE

 

1,The mixture should be sealed and stored in a dry environment at room temperature, and should be used as soon as possible, to avoid wastage.

2,The product don't belong to dangerous goods, but avoid contacting skin and eyes.

3,The product is non-toxic, has good physical inertia without stimulation and harm. The product does not contain flammable and explosive ingredients which will not cause fire or explosion without special requirement for transport.

4,Stored for a period of time, the plastic may be layered. So please stir well before using, and can't affect its performance.

5,The following substances may hinder the curing or cause the phenomenon of not cure, so it is used after simple experiments, and need to clean the site of application if necessary.

      A, incompletely cured condensation type silicone rubber.

      B.amine (amine) curable epoxy resin.

      C. ash welding (solder-flux).

 

SPECIFICATION TRANSPORT

PACKAGING

 

1,20kg/set(A10kg+B10kg), packaging with bucket.

2,1 year shelf life if stored below 25 ℃, when the product passed its expiration date, it should be confirmed without abnormal phenomenon, then that can be used.

3,These products don't belong to dangerous goods, so they can be transported as normal chemicals. But be careful of leakage.