2017 New 4CH 5V DC WIFI Light Switch Controlled by Phone APP, RF 433mhz Wireless Remote Control Switches For Garage Smart Home

1 X 4 Way 5V DC Switch

 

1 X RF 433mhz Transmitter(no battery)

 

 

Features

1 Support WIFI network. (Attention: The switch module must keep connect with wifi service.)

2 Support 433mhz RF remote transmitter control.(Can learn most 433.92mhz transmitter, like chip 2260,2262,2264,1527. Allow 16 different transmitters to control )

3 Support three working modes: momentary, interlock and self-lock control.

4 Support Max 8 timing tasks for each added device.

5 Support status tracking, home appliances status timely feedback to your App.

 

Product Specification:

1 Input voltage:  DC 5V  

2 Maximum load: 10A

3 Working temperature: 0-60 centigrade

4 Control method: WIFI +433mhz RF + Manual Button Control

5 Channels: 4 Way

6 Switch size: 69*90*30mm

7 Passive output, commonly used as a mechanical switch.

8 Remote Frequency:433mhz

9 Remote battery: A CR2025 button battery (not include)

 

 

 

How to connect phone with switch?

1 Make sure the switch and your phone under the same wifi service. 

2 Download and install the software of “eWeLink” from APP store or Google play store.

3 Follow “eWeLink” instructions to register an account on it.

4 Log in your account of “eWeLink”.

5 Press any manual control button between S1-S4 for 5 seconds until you see the D3 light flash quickly, release it. Then add device on mobile phone by eWeLink APP according its introduction.

6 Now you can use your phone to control the switch under 2G/3G/4G signal.

 

 

 

How to learn 433mhz transmitter?

1 Press “learning button” until you see LED flash 1 time, release button, then CH1 learn.

2 Press “learning button” until you see LED flash 2 times, release button, then CH2 learn.

3 Press “learning button” until you see LED flash 3 times, release button, then CH3 learn.

4 Press “learning button” until you see LED flash 4 times, release button, then CH4 learn.

 

How to clear 433mhz signal? 

Step 1: Keep pressing the "learning button" ;
Step 2: Supply power to switch;
Step 3: The LED light will flash 4 times slowly.
Step 4: Release the "learning button". OK. 

 

 

 

How to set working mode?

1 Press “mode button” until you see D8 flash 1 time, release button, now it is momentary.

2 Press “mode button” until you see D8 flash 2 times, release button, now it is interlock.

3 Press “mode button” until you see D8 flash 3 times, release button, now it is self-lock.

 

 

What is the difference between working mode?

1 Momentary: Keep pressing remote button A, receiver CH1 ON. release button A, then receiver CH1 OFF

2 Interlock: Press remote button A, receiver CH1 ON, and receiver CH2, CH3,CH4 OFF.

3 Self-lock: Press remote button A , receiver CH1 ON. press button A again, then receiver CH1 OFF

 

 

FQA

1 Where can I use this switch?

First, I have a wireless router and WIFI service in my house;

Second, I install this switch in the range of wireless router WIFI signal.

Third, I connect my phone with the switch under wireless router WIFI service.

Then you can go anywhere to control it now.

 

2 Where can I download the APP?

APP store and Google Play store---- eWeLink

 

3 Can I install this switch in my car?

Yes, but I have to install a wireless router and have WIFI service in the car, then it is Ok.

 

4 How many people can control my WIFI switch?

I can share this switch to as many people as I can.

2. After parcel sent out, it will become uncontrollable. We will appreciate your patience during the delivery period. Estimate delivery time is 20~45 days for most of the countries (except for Brazil) 

Note 1: We are not responsible for any taxes or VAT on the customs of buyer's country.

Note 2: If in 50 days you don’t receive the parcel, please contact us. We will submit a search with the shipping agent.

If during 60 days (90 days for Brazil) you don’t receive the parcel, we will issue full refund to you.