EPEVER 10A PWM Solar Charge Controller 12V LED Indicate Battery Status Temperature Sensor Digital Tube One Key Setting LS1012EPD

General Information

LS- EPD series solar charge controller adopts the most advanced digital technique and operates fully automatically. It is ideal for extreme environments with corrosion, dust, water etc and has various unique functions:

Electronic protection: Over charging, over discharging, overload, short circuit and reverse protection of solar module

High efficient Series PWM charging, increase the battery lifetime and improve the solar system performance

Widely used, automatically recognize day/night

Battery LED indicate battery status

Industrial design, wide application range

Digital tube menu, only one key solve all setting simply

Intelligent timer function with 1~13 hours option

IP67 protection

Features and Mounting

1	Charging Status LED indicator	6	Load Terminals
2	Battery Status LED indicator	7	Digital tube
3	Temperature Sensor	8	Key
4	Solar Module Terminals	9	Aluminum housing
5	Battery Terminals	10	Mounting hole Φ5

Load mode

Manual Control:Control the load via the button.

Light ON/OFF

Light ON + Timer

Note: In the mode of Light ON/OFF and Light ON/Timer, the Load is turned on after 10Min. delay.

Test Mode (Default):Test Mode is as same as Light Control Mode but no delay.

The correspondence table of Load Work Mode & LED digital tube value

Value	Working mode	Value	Working mode
0	Light ON/OFF	0.	Light ON + 8 hours
1	Light ON + 1 hours	1.	Light ON + 9 hours
2	Light ON + 2hours	2.	Light ON + 10 hours
3	Light ON + 3hours	3.	Light ON + 11 hours
4	Light ON + 4 hours	4.	Light ON + 12 hours
5	Light ON + 5 hours	5.	Light ON + 13 hours
6	Light ON + 6 hours	6.	Manual Control
7	Light ON + 7 hours	7.	Test Mode

Operation

Digital tube & Key

The digital tube display the load work mode, please refer to the correspondence table of Load Work Mode & LED digital tube value. Pressing the key to configure the parameter, please refer to the below configuration method:

1) After Powering on , disconnect the PV or connect the PV(Voltage<5V) , the light of the digital tube point go on; Connect the PV(Voltage>6V) ,the light of the digital tube point go off.

2)The key can be used to operate switching on/off the load (Manual control) or clearing the faults

3) Keeping pressing the button over 5S, It will go to the parameter in browsing mode which can cycle through the parameter item by clicking the button ,after the light of the digital tube point going on.

4) After the digital tube displaying the value what you want to configure, releasing the key and waiting 15S, Digital Tube stop flashing, then the configuration is successful.

 

Technical Specifications

LS****EPD	1012	1024	2024
Nominal system voltage	12VDC	12/24VDC Auto	12/24VDC Auto
Max. PV input voltage	30V	50V	50V
Rated current	10A	10A	20A
Equalize Voltage	14.8V(12V);29.6V(24V)
Boost Voltage	14.4V(12V);28.8V(24V)
Float Voltage	13.7V(12V);27.4V(24V)
Low Voltage Reconnect Voltage	12.6V(12V);25.2V(24V)
Low Voltage Disconnect Voltage	11.2V(12V);22.4V(24V)
Self-consumption	12V:≤4.58mA;24V;≤6.01mA
Temperature compensation coefficient	-5mV/°C/2V(25°C)
Working temperature	-35°C~+55°C
Enclosure	IP67
Overall dimension	108.5mm×75mm×25.6mm
Mounting dimension	100.5mm
Mounting hole size	Φ5
Power cable	PV/BAT/LOAD:4.0mm2		PV/BAT/LOAD:6.0mm2
Net weight	408g	410g	435g