YM-LM501  MANUEL

Foreword:

     Thank you for choosing our LED controller family, make sure you have read these instructions thoroughly before using the equipment.

     The figures in the manual are for reference only. Our products will be continually updated, but the information may not be distributed individually. The manual has been reviewed and the accuracy is guaranteed. 

Use this manual

Warnings:

•   Do not disassemble or modify the product(may lead to electric shock, fire or malfunction).
•   Do not use the product in places exposed to inflammable gases or debris such aspropane gas or gasoline (may cause explosion or fire).
•   Do not use benzene or other volatile substances (may damage the product).
•   Keep away from direct sunlight. Do not store in high temperature areas (may cause product deformation or malfunction).
•    Do not apply shock or impact to the product (may cause breakdown).
•    Do not install on an unstable location (may get  detached and result in breakdown or injury).

Security Instructions:

•    Warning:Please install the controller in the environment recommended by our technicians, we do not take any responsibilities for the consequences of any damage caused by your mis-operation.
•    Warning: Please double-check and make sure to use the power which this controller is designated. The wrong power may cause equipment damage or fire
•    Warning:The lighting output ports provide control signals forthe lighting, please choose and connect the cables and internet cables as the manual recommended. And protect the power from the thunder and other outside powers in case leading malfunction and equipment damage
•   Warning:Our controller firmware may be a little different according to different control lightings. In order to make sure your controllers can work as your designed goals please consult our engineers if you choose the third-party lightings.
•   Importance:If your controller can not work after finishing all the connecting. Do not try to disassemble the controller otherwise ourcompany will not stop providing the after-sales services.
•   Warning:Disassemble the controller while it is connected with the power is dangerous, it may  lead an electrical shock to you, or a permanent damage of controller circuit and controller components

Start knowing the controller

Front Panel

Rear Panel

1.Features

• Ethernet connection LED controller;
• Control mode: on-line control / off control;
• One output port can control 512 pixels;
• 4 output ports;
• a cascade control port.;
• Playback speed: the maximum speed of not less than 25 frames / sec;
• Power supply: AC220V ± 10V 50Hz;
• EMC design, with good anti-jamming capability;

2.Connections

3.System Configuration

         Minimum system configuration: 

         CPU: XM 266 Pentium; Memory: 64M; Space: 700M hard disk space .

        Sound Card: Directx Sound compatible .

        Graphics: Direct3D compatible (16Mb or more) .

         Recommended configuration:   

        CPU: Pentium 400; Memory: 128Mb; Space: 700M hard disk space.

        Sound Card: Directx Sound compatible.

        Graphics: Direct3D compatible (32Mb or more).

4.Settings

4.1 Playback Speed Settings

Press  FUN to enter playback speed setting menu;

Press  CFM to enter edit mode;

Press  ▲/▼ to adjust the speed;

Press  CFM to confirm the speed

Press  FUN to return to the main interface .

4.2 Brightness adjustment

Press  FUN →▲to enter the brightness setting menu;

Press  CFM  to enter the edit mode;

Press  ▲/▼to adjust the brightness;

Press  CFM  to confirm;

Press  FUN  to return the main interface.

4.3 Clock Adjustment

Press  FUN →▲→▲ to enter clock adjustment menu;

Press  CFM to enter edit mode;

Press  ▲/▼to adjust the clock;

Press  CFM  to confirm

Press  FUN to return to the main interface.

4.4 IP Address

IP addresses are consisted by 4 decimal digits (IP1.IP2.IP3.IP4), such as 192.168.1.1. IP address is one of important parameters of the controller, it will be shown on the main interface after power-on;

Press  FUN →▲→▲→▲to enter IP address setting menu,the current IP address is shown in the screen

Press  CFM to enter IP address1 edit mode;

Press  ▲/▼to adjust IP address1;

Press  CFM to confirm IP address1, then enter IP address2 edit mode.

Press  ▲/▼to adjust IP address2;

Press  CFM to confirm IP address2, then enter IP address3 edit mode.

Press  ▲/▼to adjust IP address3;

Press  CFM to confirm IP address3, then enter IP address4 edit mode.

Press  ▲/▼to adjust IP address4;

Press  CFM to confirm IP address4,four IP addresses are shown in the screen;

Press  FUN to return to the main interface.

4.5 MAC address

MAC address is consisted by six hexadecimal digits (MAC1-MAC2-MAC3-MAC4-MAC5-MAC6), such as :00-e0-b1-08-07-f3

Press  FUN →▲→▲→▲to enter MAC address settin g, the current MAC address is shown on the screen;

Press  CFM to enter MAC1 address edit mode;

Press  ▲/▼to modify MAC1 address; 

Press  CFM to confirm MAC1 address,then enter MAC2 address edit mode;

Press  ▲/▼to modify MAC2 address;

Press  CFM to confirm MAC2 address,then enter MAC3 address edit mode;

Press  ▲/▼to modify MAC3 address;

Press  CFM to confirm MAC3 address,then enter MAC4 address edit mode;

Press  ▲/▼to modify MAC4 address;

Press CFM to confirm MAC4 address,then enter MAC5 address edit mode;

Press  ▲/▼to modify MAC5 address;

Press  CFM to confirm MAC5 address,then enter MAC6 address edit mode;

Press  FUN to return to the main interface.

5 . Main set Software Setting

5.1. You need set the controller IP address before the main set software can communicate with the controller.

5.2. Run "LED display software" (V2.844 or above) and select "o nline /offline”, shown as below:

5.3. After you’ve done setting the IP  address, you can play the patterns.