Model number:JM-DT17
Product name:2.4G 4 zone touch LED Dimmer
Technical Parameters
● Working temperature:-20~55℃
● Supply voltage:DC12V~24V
● Output:2 Channel(2 channel are the same effect)
● Connection mode:Common anode
● Controller size:L152×W41×H28mm
● Net weight:105g
● Static power consumption:<1W
● Output current:<6A/CH
● Output power:12V:<144W;24V:<288W
Remarks:One Remote have 4 Group, each Group can control many pieces controller,and each Group can be control separately, and 4 Group can be control together.Easy to used 1%-100% brightness dimer-able. .
 

This 4 zone 2.4G RF led dimmer adopt the touch color wheel and press button RF wireless remote control,can adjust brightness infinitely to change the lights brightness according to the customer's preference. 2.4G frequency make it more stable and more strong anti-jamming capability to use.

Besides, one remote can controlled 4 group of light independent,make it realize the one-to-many manipulation control.

External dimension

 

 

Connection description:

Power input interface:
   Adopt male and female connector with screw.

Load output interface:
 Adopt male and female connector with screw.

Direction for use

 

The Remote control parameter are as below table:

●Function introduction:
1.Use the 2.4G frequency RF remote control, no need to make the remote direct to the controller,and the RF remote can controlled it across obstacles.
2.In the open area remote control distance is about 30 meters.
3.Adopt the press key and touch wheel control remote, slightly touch the color wheel can adjust the light’s color temperature smoothly .   
● Operation method:
1.Connect the load wire at first, following by the power wire; Please ensure short circuit can not occur between connecting wire before you turn on the power;
2.Only the power button is effective in the OFF station, press the power button for the first time then controller will enter to the last mode before turn of the controller last time (memory off function).
 3.Group operate instruction: if there is A and B two piece controller receiver, first to Power the receiver A, then press the “Group 1 ON” button for five times then the led will be flash, this means receiver A is controlled by Group 1. Second to power the receiver B,press the “Group 2 ON” button for five times, than the led will be flash, this means the Receiver B is controlled by Group 2. When press the “Master ON” button, Receiver A and B are turn on at the same time, press the “Master OFF” button, Receiver A and B are turn off at the same time , A and B receiver are changing the same when press the touch color wheel . IF you want to controller receiver A/B separately, please press the “Group 1 ON” button first, than you can adjust Receiver A brightness or turn ON/OFF receiver A . Meanwhile, Group 2/3/4 are the same.
Remarks: One remote can control 4 group of receiver at the same time ,each Group can be
including several receiver, such as 40 Receiver divided into four groups On average, the remote control can control 10 pieces receiver in each group , and achieve the synchronous effect .

● Match code and clean code Instruction:
For a new combination, the remote must to match code withe the receiver then it can be used normally. Before match code, you must ensure the LED Controller, power supply and led light are connected correctly, then cut off the power ,and re-power it again.
Match code:Please press the “Group X(X=1,2,3,4) ON”Button for 5 times within 8 seconds after power the controller, then the output led light will be flash for 6 times, this means the remote is match code with this receiver successfully, they can used normally.
Clean code: if user want to change the light control group,he can clean the code off. After clean code the remote and receiver will be in the initial state. Operation method: Press the “Group X(X=1,2,3,4) OFF ” Button for 5 times within 8 seconds when power the controller, till the output light flash for 6 times, means clean code successfully.
Remarks:The regular product for sale is a kit (one remote and 1 receiver). The user can re-programmed freely as needed. One remote can control countless receivers, but one receiver can only be controlled by two remotes max.

Typical Application

Model number:JM-SW17
Product name:2.4G 4 zone touch color temperature controller
Technical Parameters
   ● Working temperature:-20~55℃
   ● Supply voltage:DC12V~24V
   ● Output:2 Channel(2 channel are the same effect)
   ● Connection mode:Common anode
● Controller size:L152×W41×H28mm
● Net weight:105g
● Static power consumption:<1W
● Output current:<6A/CH
● Output power:12V:<144W;24V:<288W 
Remarks:One Remote have 4 Group, each Group can control many pieces controller,and each Group can be control separately, and 4 Group can be control together.Easy to used .

This 4 zone 2.4G RF led dimmer adopt the touch color wheel and press button RF wireless remote control,can adjust brightness infinitely to change the lights brightness according to the customer's preference. 2.4G frequency make it more stable and more strong anti-jamming capability to use.

Besides, one remote can controlled 4 group of light independent,make it realize the one-to-many manipulation control.

External dimension 

Connection description:
Power input interface:
Power : Adopt male and female connector with screw.

Load output interface:
  Adopt male and female connector with screw.

Remote Control Function

The Remote control parameter are as below table:

 

Direction for use
●Function introduction:
1.Use the 2.4G frequency RF remote control, no need to make the remote direct to the controller,and the RF remote can controlled it across obstacles.
2.In the open area remote control distance is about 30 meters.
3.Adopt the press key and touch wheel control remote, slightly touch the color wheel can adjust the light’s color temperature smoothly .   
● Operation method:
1.Connect the load wire at first, following by the power wire; Please ensure short circuit can not occur between connecting wire before you turn on the power;
2.Only the power button is effective in the OFF station, press the power button for the first time then controller will enter to the last mode before turn of the controller last time (memory off function).
 3.Group operate instruction: if there is A and B two piece controller receiver, first to Power the receiver A, then press the “Group 1 ON” button for five times then the led will be flash, this means receiver A is controlled by Group 1. Second to power the receiver B,press the “Group 2 ON” button for five times, than the led will be flash, this means the Receiver B is controlled by Group 2. When press the “Master ON” button, Receiver A and B are turn on at the same time, press the “Master OFF” button, Receiver A and B are turn off at the same time , A and B receiver are changing the same when press the touch color wheel . IF you want to controller receiver A/B separately, please press the “Group 1 ON” button first, than you can adjust Receiver A brightness or turn ON/OFF receiver A . Meanwhile, Group 2/3/4 are the same.
Remarks: One remote can control 4 group of receiver at the same time ,each Group can be
including several receiver, such as 40 Receiver divided into four groups On average, the remote control can control 10 pieces receiver in each group , and achieve the synchronous effect .


● Match code and clean code Instruction:
For a new combination, the remote must to match code with the receiver then it can be used normally. Before match code, you must ensure the LED Controller, power supply and led light are connected correctly, then cut off the power ,and re-power it again.
Match code:Please press the “Group X(X=1,2,3,4) ON”Button for 5 times within 8 seconds after power the controller, then the output led light will be flash for 6 times, this means the remote is match code with this receiver successfully, they can used normally.
Clean code: if user want to change the light control group,he can clean the code off. After clean code the remote and receiver will be in the initial state. Operation method: Press the “Group X(X=1,2,3,4) OFF ” Button for 5 times within 8 seconds when power the controller, till the output light flash for 6 times, means clean code successfully.
Remarks:The regular product for sale is a kit (one remote and 1 receiver). The user can re-programmed freely as needed. One remote can control countless receivers, but one receiver can only be controlled by two remotes max.
Typical Application
 

Number Number:JM-QC17
Product Name:2.4G Plastic shell Touch RG  B   Controller
Technical Parameters
● Working temperature:-20~60℃
● Supply voltage:DC12V~24V
● Output:3 Channel
● Connection mode:Common anode
● Controller size:L152×W41×H28mm
● Net weight:105g
● Static power consumption:<1W
● Output current:<6A/CH
● Output power:12V:<216W,  24V:<432W
Remarks:This remote are not support 4 group control version. The “W” button is the “RGB” mix color.
 

This 4 zone 2.4G RF remote RGB led controller adopt the most advance PWM control technology, can control all kinds of 3 channel (common anode) LED lights. Such as LED module, led strip, led control box, led source,etc. This controller is with indicating light and power off memory function, next time to used it, will start with the model it save.  Easy connection and simple to used is the representative advantages of this controller. User can choose different changing mode, adjust the speed and brightness,turn on/off by the remote control according to their preference .

External dimension

 

                                                               (Receiver size)

                                                  (Remote size)

Connection description:
Power input interface:
   Adopt male and female connector with screw

Load output interface:
 Adopt male and female connector with screw.

Remote Control Function

The Remote control parameter are as below table:

Direction for use

●Function introduction:

1.Use the 2.4G frequency RF remote control, no need to make the remote direct to the controller,and the RF remote can controlled it across obstacles.

2.In the open area remote control distance is about 30 meters.

3.Adopt the press key and touch wheel control remote, slightly touch the color wheel can adjust the light’s color smoothly .  

● Operation method:

1.Connect the load wire at first, following by the power wire; Please ensure short circuit can not occur between connecting wire before you turn on the power;

2.Only the power button is effective in the OFF station, press the power button for the first time then controller will enter to the last mode before turn of the controller last time (memory off function).

3.In ON station,only press the “MODE+” button or “MODE -”button to choose the the former or later mode, total are 28 modes as below table:

 

4.When in the cycle mode ,Press the “MODE +” Button it will turn into“Static Red MODE”(The 1^st mode). Press the “MODE -” Button it will turn into the “White stroboscopic MODE”(The 27^th mode)

5.Press the “MODE+/MODE -” Button when is in the touch color wheel adjust color mode, it will turn into “Static Red mode”(the first mode)

6.Long Press “Speed +/Speed -”or “Brightness +/Brightness -” button can quickly adjust the speed/brightness.

● Match code and clean code Instruction:

Match code:For a new combination, the remote must to match code withe the receiver then it can be used normally.

Please press the ON Button for 5 times within 8 seconds when power the controller, then the output led light will be flash for 6 times, this means the remote is match code with this receiver successfully, they can used normally.

Clean code: if user want to change the light control group,he can clean the code off. After clean code the remote and receiver will be in the initial state. Operation method: Press the OFF Button for 5 times within 8 seconds when power the controller, till the output light flash for 6 times, means clean code successfully.

Remarks:The regular product for sale is a kit (one remote and 1 receiver). The user can re-programmed freely as needed. One remote can control countless receivers, but one receiver can only be controlled by two remotes max.

Typical Application

 

 

 

Number Number:JM-QC17W
Product Name:2.4G Plastic shell Touch RGBW Controller
Technical Parameters
● Working temperature:-20~60℃
● Supply voltage:DC12V~24V
● Output:4 Channel
● Connection mode:Common anode
● Controller size:L152×W41×H28mm
● Net weight:110g
● Static power consumption:<1W
● Output current:<6A/CH
● Output power:12V:<216W,  24V:<432W    
Remarks:This remote are not support 4 group control version.

This 2.4G Plastic shell Touch RGBW Controller adopt the most advance PWM control technology, can control all kinds of 4 channel (common anode) LED lights. Such as LED module, led strip, led control box, led source,etc. This controller is with indicating light and power off memory function, next time to used it, will start with the model it save.  Easy connection and simple to used is the representative advantages of this controller. User can choose different changing mode, adjust the speed and brightness,turn on/off by the remote control according to their preference .

External dimension:

 

 

Connection description:
Power input interface:
   Adopt male and female connector with screw

Load output interface:
Adopt male and female connector with screw.

Remote Control Function

The Remote control parameter are as below table:

Direction for use

●Function introduction:

1.Use the 2.4G frequency RF remote control, no need to make the remote direct to the controller,and the RF remote can controlled it across obstacles.

2.In the open area remote control distance is about 30 meters.

3.Adopt the press key and touch wheel control remote, slightly touch the color wheel can adjust the light’s color smoothly .  

● Operation method:

1.Connect the load wire at first, following by the power wire; Please ensure short circuit can not occur between connecting wire before you turn on the power;

2.Only the power button is effective in the OFF station, press the power button for the first time then controller will enter to the last mode before turn of the controller last time (memory off function).

3.In ON station,only press the “MODE+” button or “MODE -”button to choose the the former or later mode, total are 28 modes as below table:

 

4.When in the cycle mode ,Press the “MODE +” Button it will turn into“Static Red MODE”(The 1^st mode). Press the “MODE -” Button it will turn into the “Single white flash MODE”(The 27^th mode)

5. Press the “MODE+/MODE -” Button when is in the touch color wheel adjust color mode, it will turn into The last of the selected mode.

6.Long Press “Speed +/Speed -”or “Brightness +/Brightness -” button can quickly adjust the speed/brightness.

● Match code and clean code Instruction:

Match code:For a new combination, the remote must to match code withe the receiver then it can be used normally.

Please press the ON Button for 5 times within 8 seconds when power the controller, then the output led light will be flash for 6 times, this means the remote is match code with this receiver successfully, they can used normally.

Clean code: if user want to change the light control group,he can clean the code off. After clean code the remote and receiver will be in the initial state. Operation method: Press the OFF Button for 5 times within 8 seconds when power the controller, till the output light flash for 6 times, means clean code successfully.

Remarks:The regular product for sale is a kit (one remote and 1 receiver). The user can re-programmed freely as needed. One remote can control countless receivers, but one receiver can only be controlled by two remotes max.

Typical Application

 

 

Package includes

RF=1 piece Remote (Battery is not included)
or 1 piece dimmer
or Kit=1 piece dimmer +1 piece remote (Battery is not included)