welcome to our store

30 channel /27channel Easy DMX led rgb controller 5v/12/24v 360w

Welcome to use the 30CH constant decoder, which take advantage of advanced microelectronic control technology. This technology changes the international fashion DMX512/1990 standard digital control signals into analog control signals. There are 1 ~ 30 output channels; each channel can achieve 256 control levels. This constant decoder is used when DMX512 control equipment control general LED lighting.

 

Products Performance:

Input Power:  DC9V-DC24V                                         Maximum load current:  2A/CH×30

Maximum power load: 360W (12V) 720W (24V)         Output gray level: 256

Input Signal:  DMX512/1990                                           Output signal:  30 channels Constant PWM

Output DMX :  30 channels                                             standard XLR-3 caron plug

Size:  L225*W80*H32                                                      Weight(Gross Weight):300g

 

Basic functions:

There are 30 output channels, can connect with single or RGB lamps;

0-100% dimming output, each channel 256 gray levels

International standard DMX512 input protocol, address code set by DIP switches;

Wide voltage DC input DC9V ~ DC24V;
Each occupied by 30 DMX address.

The decoder comes with 16 kinds of test patterns, 16 levels for rate of change

Decoder to use:

Note: FUN = OFF (the tenth code switch up) means to accept DMX512 signal mode

The first DMX address setting:
The decoder set the address bit by coding switch, of which 1-9 is for setting the start address of the Binary numeric code switch of DMX512, the first one is the lowest position, the ninth one is the highest
Bit of address code can be set to 512.

DMX512 start address code is the sum of switches 1-9, at the same time turn downside of the code switch (ON set to "1"), then the value of the bit can be gotten; coding switch up (set to "0"), the value of the bit is 0.
 

Note: It will be Automatic operation mode when the No. 10 switch is turned down.

Effect choice (button switch No.1 to No.4):

1, Push No.1: Automat cycling.             2, Push No. 2: Seven-color gradual cycle changing.

3. Push No.1 &2: RGB Fade in and out    4. Push No.3: Severn color jumping

5. Push No.1 & 3: RGB  jumping.         6. Push No.2 & 3: Red color.

7. Push No. 1 & 2 & 3:Green color.         8. Push No.4: Blue color.

9. Push No.1 & 4: Yellow.                10: Push No.2 & 4: Violet.

11. Push No.1 & 2 & 3: Cyan.             12. Push No.3 & 4: white.

13. Push No.1 & 3 & 4: Seven-color gradual cycle changing and jumping.    

14. Push No.2 & 3 & rgb-color gradual cycle changing and jumping.

15. Push No.1 & 2 & 3 & 4: Seven-color jumping and rgb-color jumping.

Speed Choices (Button Switch No.5 to No. 8)

1.        Push No.5: 0.5 second. 2. Push No.6: 1 second. 3. Push No.7: 1.5 second. 4. Push No.8: 2 second.

 

 

 

 

There are three kinds of using method:

 

 

 

 

 

 

 

 

 

 

if you want to 5 v input, the connection is as follows :

 

 

if you need to connect two power supply, the connection is as follows:

 

 

Schematic for System Connection:

 

Installation Notes:

 

@  This kind of controller works only under DC5V-24V, which is provided by the matched controllable main power, or else the controller will be damaged.

 

@  The UTP wire is connected hand in hand to make the cable, when two or more controller connected.

 

@  The power supply should be off when connecting the electric wires, and it can be turned on till making sure the wires are connected correctly and the indicator of main power in red is lighting.

 

@  Controller should work under the environment of adequately ventilated, dry, not corroded, no flammable gas and rust.

 

Please check the wires connection regularly so that the wires of aged, rust-eaten, and damaged insulation spacer can be replaced timely