| Motor Type: | DC Motor |
|---|---|
| Model Number: | 400W brushless spindle |
| Unit Type: | piece |
| Package Size: | 10cm x 8cm x 12cm (3.94in x 3.15in x 4.72in) |
| Package Weight: | 1.5kg (3.31lb.) |
Quick Details
Specifications
the motor take the ER11 3.175MM collet; if you need other collet, please contact for enquires! tks!
Characteristics of brushless motor:
The spark produced 1, no brush, low interference, no motor brush to remove the brush, changes in the most direct is that there is no brush motor running, thus greatly reduced electric spark interference of radio remote control equipment.
2, low noise, smooth running, brushless motor without brush, running friction is greatly reduced, running smoothly, the noise will be much lower, this advantage for the stability of the equipment is a huge support.
3, long service life and low maintenance costs, less brush, no motor brush wear is mainly in bearing, from the mechanical point of view, no brush motor is almost a maintenance free motor, (the lowest life is a brushless DC motor is 10 times higher than necessary, as long as do some dust removing maintenance can be. On the next comparison, we know that the advantages of brushless motor relative to the brush motor where the.
Spindle motor: a new brushless DC motor (imported NSK bearing)
Working voltage: 48VDC need to brushless drive, motor can run
Power: 400W
Speed: 12000r/min
Torque: 0.5294 (N.m)
Insulation resistance: >2 MB
Dielectric strength: 400V
Motor diameter: 57mm (fixed parts of the body is 55mm)
The output shaft of the motor from the previous 8mm to 10mm.
Chuck: length of part cutter parts (including 35mm, nut and sandwich 43mm)
Chuck: part of the diameter of 16mm
Motor length: 174mm (including the clamping part and motor)
Spindle net weight: 1.22KG
The spindle is about 0.01-0.03.
Can be used for engraving metal or nonmetal materials.
The spindle comes with forced air cooling, can work for a long time.
Brushless DC (BLDC) motor controller
First, product features:
1, model: HX-WS400
2, working voltage: DC18V-DC52V
3, drive current: rated 10A, peak value 15A.
4, drive power: less than 500W (related working voltage)
5, closed loop steady speed, large load, the motor can still keep speed
6, pure hardware design, high speed, high anti-interference ability
7, external potentiometer control, analog voltage 0-5V and PWM speed control (MACH3 control)
8, positive inversion control, soft switching function
9, over current short circuit protection and instructions (red indicator)
10, with EN enable control
Name Description
DC- DC+ DC voltage input DC18-52V
U V W motor phase
HALL+ Holzer power cathode
HB HC HA Holzer signal line
HALL- Holzer power cathode
+5V control signal power +5V
VR speed control signal input
GND control signal power supply to the public side
F/R positive / reverse control signal
PWM PWM frequency (MACH3)
EN enable control input
Two, function description:
(1) speed regulation mode
1, the default potentiometer, can be directly through the rotary potentiometer
2, analog control, VR pin voltage signal input terminal, GND foot ground (voltage range 0-5V) (note the external voltage signal control need to be removed from the potentiometer control to take effect, no one can not control)
3, can use connected PWM signal input control, PWM input requirements: level 3.5-12V VPP, frequency 1K-10KHZ applicable to Mach3 spindle speed control, (note external PWM signal control need to tear down the control potentiometer to take effect, or cannot control).
(2) motor run / stop control (EN)
1, control terminal EN relative to the GND can control the stop and operation of the motor. EN pin suspended motor operation, when the motor is connected with the GND terminal when the motor is stopped.
(3) motor forward / reverse control (F/R)
1, control the F/R and +5V can control the direction of the operation. When F/R and +5V are not connected, the motor runs counter clockwise, and vice versa.
Special power supply for 400W air cooling spindle motor
Input voltage: 50/60HZ AC110/220V, can be switched, global universal
Output voltage: DC48V
Output power: power 400W with temperature control cooling fan
Power net weight: 0.9KG
Power size: long 215* wide 115* high 50
