60W 24VDC 3000rpm 0.2N.m Brushed DC Servo Motor Driver kit 1000 line D=60mm JMC 60JZS0630AS+MCDC706

Package including:

1pcs DC Servo Driver MCDC706

1pcs Brushed DC Servo Motor 60JZS0630AS

 

DC Servo Driver MCDC706:

Working voltage:24-50VDC
Optical coupling isolation servo reset input interface ERC
Have real-time virtual oscilloscope, can display the parameter curve about the motor running current, speed ,tracking error and so on.
Can set the PID parameters of position loop, speed loop and current loop.
You can choose the encoder according the encoder cable. and you can setting pulse equivalent according the inside electronic gear ratio.
Using RS232C port, through PC testing software change parameter.
Over-current, I²T, overvoltage , undervoltage, overheating, speeding and differential protection
When the indicator light turns green, it means running. when the indicator light turns red, it means protection or offline.

 

Typical applications

Suitable for inkjet printing and dispensing machine.

 

Performance indicators:

MCDC706 is all-digital DC servo drive system adopts high-performance digital signal processor (DSP) and integrated circuit, and come out to be a cost effective product with simple circuit, high integration, easy operation, and strong practicability. MCDC706 provide three feedback loops:(position loop, velocity loop and current loop). Three work control mode: position, velocity and torque. MCDC706 matches with DC servo motor under 24~50V and 30~300W. 

Electrical indicators:

Instructions	Min	Typical values	Max
Supply voltage (VDC)	24V	36V	50V
Output current (A)	-	6	-
Input current (mA)	-	10	-
Work pulse frequency (KHZ)	-	-	250
Low level pulse time (US)	2.5	-	-

 

Environmental indicators:

cooling	natural cooling or forced convection
Environment	Space	Avoid dust,oil frost and corrosive gases
	Work temperature	0~+50°C
	Storage temperature	-20°C~+80°C
	Humidity	40~90%RH
Dimension	-	118×76×35
Weight	-	300g

P1 input signal interface description:

symbol	function	Description
PUL+	Input signal photoelectric isolation positive end	Connected to the +5V power supply, +5V~+24V can be driven, higher than +5V need to limit the current resistance
PUL-	Step pulse signal	Down along the effective, whenever the pulse from high to low when the motor to take one step, the input resistance 220ohm, the requirements: low level 0-0.5, high level 4-5V, pulse width of less than 2.5US
DIR+	Input signal photoelectric isolation positive end	Connected to the +5V power supply, +5V~+24V can be driven, higher than +5V need to limit the current resistance
DIR-	Direction control signal	For changing the motor steering, input resistance 220ohm, requirements: low level 0-0.5, high level 4-5V, pulse width less than 2.5US
ERC+	Input signal photoelectric isolation positive end	Connected to the +5V power supply, +5V~+24V can be driven, higher than +5V need to limit the current resistance
ERC-	Motor release signal	Active (low level) to cut off the motor coil current, the driver stops working, the motor is in a free state
ALLM+	Alarm output positive
EGND	Alarm output negative pole

 

P2 motor encoder interface description

Terminal number	symbol	symbol	Name	description
1	Motor line	S-	DC brushed motor - end
2		S+	DC brushed motor +end
3		VDC	Input DC power supply+	DC24V-50V
4	Power input	GND	Input ground	0V

Brushed DC Servo Motor 60JZS0630AS:

1: high performance, smooth, high precision and low noise

2: ultra low cost, far below the AC servo

3: the surrounding interference is much lower than the AC servo

4: optional 1000 or 500 wire encoder, the positioning error can be as small as 1 pulses.

 

Electrical parameters of DC servo motor

			58JZS0630AS	58JZS1030AS	58JZS1730AS	28JZS2030AS	80JZS2530AS
Vt	voltage	V	24	30	36	36	48
No	Idling speed	RPM	4200	4100	4000	4250	4000
Io	No-load current	Amps	0.25	0.4	0.36	0.45	0.6
Tc	Holding torque	mN.m	198	304	523	600	760
Nc	Rated speed	RPM	3000	3200	3200	3200	3000
Ic	Rated current	Amps	3.8	4.9	6.4	7.8	8.5
Po	Rated power	Watts	60	100	175	200	250
Tp	MAX toruqe	N.m	0.72	1.44	2.72	2.8	3.5
Ip	Max current	Amps	12	20	30	34	40
Ke	EMF constant	V/KRMP	5.8	7.3	9.1	8.5	10
Kt	Torque constant	mN.m/Amp	55	69.9	86.8	81.2	95
Rt	Terminal resistance	Ohms	1.9	1.45	1.15	1.05	2.0
H	inductance	mH	3.2	2	1.7	1.28	1.8
Jm	Moment of inertia	Kg.cm²	0.133	0.325	0.565	0.661	0.83
L	Motor length	mm	100	127	160	171	160
W	weight	Kg	0.8	1.2	1.7	1.9	2.4

Payment

1. If you have any difficulty in paying your items, pls contact us first and we will soon help to solve it.

 

Shipping

1. Rule all items will be shipping within 3-5 business days after you placed order.

2. UPS/DHL/FedEX express shipping usually takes 3-7 working days depended on the country delivered to. We will choose the best and most suitable shipping for you.

3. Customer should pay for the custom fee in any case.

4. We are not responsible for any accidents, delay or other issues that are the responsibility of the shipping service.

 Warranty& Return Policy

1. The items are ALL BRAND NEW .All products have been checked and packaged in good condition before dispatch.

2. You have 14 days to return the items from the date they were received. If the items are your possession more then 14 days, we would provide the 12 months Manufacturer’s for defective items.

3. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and your ID.

4. Return shipping is to be paid by the buyer.