| Motor Type: | Stepper Motor |
|---|---|
| Unit Type: | piece |
| Package Size: | 30cm x 20cm x 10cm (11.81in x 7.87in x 3.94in) |
| Package Weight: | 0.6kg (1.32lb.) |
Quick Details
Specifications
Description:
NVEMv1.1 support Mach3 software and standard MPG,through Ethernet to communicate with computer,just use the Twine to connect directly or transfer with router.
NVEMv1.1 motion controller adopts the ARM design framework.The ARM design includes communication,codeanalytic,underlying algorithm and pulse gerneration. Rational design,reliablecontrol,convenient operation.
- 12 ports photoelectric isolated input interface for ordinary digital data;
- 10 ports photoelectric isolated output interface for ordinary digital data;
- 1 port 0-10V spindle speed analog output interface(can change to PWM output);
- can support 4 axis stepper systems, 200KHz pulse output for every axis;
- ARM motion control chip;
- main device is 12V-32VDC power supply input, current should higher than 0.5A;
- Compatible with MPG input,support the digital display MPG from our company.
Appearance and struction size
NVEMv1.1 motion controller is with the sealed shell structure,there are 4pcs setting holes at the bottom.We can fix 4pcs 4mm diameter holes at the cabinet,and install the controller into the cabinet.
The products overall size is 163.1mm*80.8mm*27.8mm;
The bottom install size is 101.4mm*42.5mm
substantival explanation
When operate the NVEM,where will be a lot of English abbreviation,now we list all of them for your kindly references:
FRO:Feedingadjust:During the operating process,the F value already set,and need to adjust the current feeding speed, then we can adjust FRO value to realize it.
SRO: Spindle speed adjust: During the operating process, the S value already set, and need to adjust the current spindle speed, then we can adjust SRO value to realize it :
Current Speed S#=setting S*SRO.
SRJ:speed adjust manually
During the operating process,as the manual speed already set,and we need to adjust the current speed,and impossible to fix the value during it is working,then we can revise the SRJ value to realize it.
Current manual speed FS#=Setting manual speed*SRJ.
F:Feedingspeed,the unit is mm/min.For example F=200,means every minute feeding 2000mm.
S: Spindle Speed. Unit is rad/min.For example S=20000,means 20000 revolution/Minute.
X axis Coordinate
Y axis Coordinate
Z axis Coordinate
A axis Coordinate
B axis Coordinate
C axis Coordinate
Ready:ReadyMode.In the mode we can do any operation,include processing or values modification or starting 2nd mode.
Reset: Reset mode.In this mode,it should stop every operation.
“Step”:Manual Step Mode. Every axis candonduct the manual step operation at this mode.
MPG: MPG mode.Every axis can conduct the MPG operation at this mode.
Device Power supply Solution
The power supply solution in the field of the Industrial automation is always very complicated,there is a lot of the GND,now we descript the structure of the power supply as below: The power supply structure as the Figure 2-1,main power supply input and MPG module and stepper control output module are common GND,Limited and Estop input module and Spindle speed adjust M3/M8/M1 module are common GND,between main power supply and output module there are photoelectric isolation.The inputs of limited switch and Estop and so on are Common anode, inside of the device, there is +12VDC as common+,no need to connect external power supply. Based on the reference of output GND interface, output a 0-10V adjustable voltage to adjust the the spindle speed,M3/M8/M10 digital output interface is open-GND. If connect an external relay,need to output GND to refer to,and give the relay an external power supply.
For more information, please contact us to send the usermanual via E-mail.
Package:
1X motion controller
1X cable