4 Axis Nema23 Stepper Motor Driver CNC Kit + 2pc Power Supply + 5Axis Breakout Board + Cable CNC Kit

Package Including:

• 4 x MB450A Sumtor step motor drive 2ph 24~50VDC 1.1~4.2A
• 4 x 57BYG 2ph Hybrid stepper motor 57HS11242A4 L 112mm 4-lead 4.2A 3NM 1.8 degree ( the default stepper motor is single shaft, if need the dual shaft stepper motor, please leave message to us in order, please kindly note it. :) )
• 2 x Switching Power Supply 350W 36V 9.7A for CNC Router Kits 115V/230V S-350-36
• 1 x 5 Axis CNC Breakout Board Interface For Stepper Motor Driver (offer for free)
• 1 x DB25 Parallel Cable & USB Power Cable (offer for free)

Stepper motor: 57HS11242A4

• Product specifics:
• Shaft length: 21mm D Single flat
• Shaft: 8mm milling flat of 0.5mm
• is customized : yes
• holding torque: 3nm
• type: hybrid
• phase: 2
• current : 4.2A
• certification: CCC,CE, ISO
• step angle: 1.8 degree
• Wiring Connection: Black(A+), Green(A-), Red(B+), Blue(B-)

Step Angle (º)	Rated Current (A)	Phase Resistance (ohm)	Phase Inductance (mH)	Holding Torque (N*m)	Detent Torque (N*cm)	Rotor Inertia (g*cm2)	Motor Length  (mm)	Motor Wire  (No.)	Motor Weight    (g)
1.8	4.2	1.4	1.8	3	12	800	112	4	1400

 

Stepper driver: MB450A

Item	Min	Typical	Max	Unit
Power supply	24	36	50	V
Average output current	1.1	2.5	4.2	A
Logic input current	6	15	30	mA
Impulse response frequency	-	-	100	KHZ
Pulse low level	5	-	1	μS

Wiring Description

Signal	Function
PUL	Pulse signal: rising edge, the pulse from low to high is to go a step angle motor
DIR	Direction signal: TTL-level driver to change the direction
OPTO	Optocoupler drive power
ENA	Enable signal: block or allow the drive to work, low-level ban
GND	DC power supply ground
+V	DC power supply positive (typical 24VDC)
A+	Motor Phase A
A-	Motor Phase A
B+	Motor Phase B
B-	Motor Phase B

Power supply: S-350-36

Model	S-350-36
DC Output	36V 9.8A
Wave and Noise	120mVp-p
Inlet Stability	±0.1%
Load Stability	±0.3%
Efficiency	85%
Adjustable range	32V~39V
AC Input Voltage	93~132V/176~264VAC Selected by  Switch
AC Input Current	3.54A/115VAC 1.73A/230VAC
Working Temperature	-10~50°C
Safety Standards	GB4943, UL60950, EN60950
EMC Standards	GB9254, 55022, Class A
Weight	1.1kg

5 axis CNC Breakout Board:

Feature

• High performance, cost-effective.
• Maximum support 5-axis stepper motor driver controllers.
• Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software.
• USB power supply and peripherals powered phase are separated to protect computer security.
• All the signals are opto-isolated which can protect your computer security.
• 5-input interface to define the Limit, Emergence-Stop, Cutter alignment etc.
• Wide input voltage range: 12-24V, and with anti-reverse function.
• One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
• Output 0-10V analog voltage for inverter to control the spindle speed.

Electrical properties (ambient temperature Tj = 25C pm):                                                             

Input Voltage	USB port from PC  or 12-24V power supply(optional)
Drive type	Pulse and Direction Signal Control
Suitable Micro step Driver	2 Phase Micro step Driver
Net weight	Approx 75g
Dimensions	90 * 70 * 20mm (L*W*H)