| Motor Type: | AC Motor |
|---|---|
| Model Number: | FC300-2.2T4 |
| input: | three-phase AC380V |
| output: | 3 phase 0-380v 5.5A |
| frequency: | 0-1000hz |
| power: | 2.2kw 3HP |
| Name: | best |
| Unit Type: | piece |
| Package Size: | 25cm x 20cm x 40cm (9.84in x 7.87in x 15.75in) |
| Package Weight: | 4.0kg (8.82lb.) |
Quick Details
Specifications
BEST 2.2kw 3HP 1000HZ VFD Inverter Frequency converter 3phase 380v input 3phase 0-380v output 5.5A for Engraving spindle motor
Single phase 220V Class
| Power(kW) | 0.75 | 1.5 | 2.2 | 3.0 | 3.7 | 5.5 | 7.5 | 11 | 15 | 18.5 | |
| Applicable Motor(kW) | 0.75 | 1.5 | 2.2 | 3.0 | 3.7 | 5.5 | 7.5 | 11 | 15 | 18.5 | |
| Input Rating | Current(A) | 7.5 | 11 | 16 | 22 | 27 | 36 | 49 | 73 | 96 | 111 |
| Voltage(V) | Single Phase 220V | ||||||||||
| Frequency(HZ) | 50/60Hz | ||||||||||
| Output Rating | Current(A) | 5 | 7 | 11 | 15 | 18 | 25 | 33 | 49 | 65 | 75 |
| Voltage(V) | Three phase 0~220V | ||||||||||
| Frequency(Hz) | 0~1000Hz | ||||||||||
| Overload protection | 200% over current immediately 150% 1 minute | ||||||||||
Three phase 380V Class
| Power(kW) | 0.75 | 1.5 | 2.2 | 3.0 | 3.7 | 5.5 | 7.5 | 11 | 15 | 18.5 | |
| Applicable Motor(kW) | 0.75 | 1.5 | 2.2 | 3.0 | 3.7 | 5.5 | 7.5 | 11 | 15 | 18.5 | |
| Input Rating | Current(A) | 4.0 | 6.3 | 8.2 | 12 | 14.5 | 19 | 25 | 33 | 46 | 52 |
| Voltage(V) | 3ph 380V | ||||||||||
| Frequency(HZ) | 50/60HZ | ||||||||||
| Output Rating | Current(A) | 2.7 | 4.2 | 5.5 | 8.0 | 9.5 | 13 | 18 | 24 | 32 | 38 |
| Voltage(V) | 3ph 0~380V | ||||||||||
| Frequency(Hz) | 0~1000Hz | ||||||||||
| Overload protection | 200% over current immediately 150% 1 minute | ||||||||||
Frequency control
1.Range: 0.0~1000.00Hz
2.Other functions: Lower limit frequency, start frequency, frequency of parking, three jumping frequency can be set respectively
3.Precision: Digital: 0.01% (10~40 centigrade degree ); Analog: 0.1% (25±10 centigrade degree)
4.Keyboard set way: 0.01 Hz can be directly to setting by up and down.
5. Analog set way: external voltage 0 to 5V, 0 to 10 V, 4-20 mA, 0 to 20 mA
Connecting mode
1. L N connect to single phase 220V voltage(part of zero line and live line).while R S T to three phase voltage.
2. U V W connect to spindle motor. The 1,2,3 pin of spindle motor plug connect converter U,V,W. That is: 1- U,2-v,3-w,4 is ground wire. If spindle motor rotated reverse, Please send any two thread swap places
3.Control com is comcon terminal ,X2 low speed ,X3 middle speed ,X4 high speed(for NCStudio card,DSP or Analog control mode)
Adjust converter parameters
1. external terminal control :Press cancel button:P000 turn into P087, confirm -0- turn into 101,display H0.0
2.Turn into manual control: press cancel button, P000 turn into p065,confirm that is 0,display P064,then press cancel button ,display H0.0, Rotate knob to H400.0(when the spindle is 400hz) or other, converter display a number multiply by 60,the results is the rotating speed. Press the operation or stop then ok.
