Structure of FPC
According to the number of layers of conductive copper foil, FPC can be divided into single
Layer circuit, double layer circuit, multi-layer circuit, double sided and so on. 

Single-layer structure: the flexible circuit of this structure is the simplest structure of the
Flexible PCB. Usually the base material (dielectric substrates) + transparent rubber(adhesive)
+ copper foil is a set of purchased raw materials(semi-manufactures), the protective film
and transparent glue are another kind of bought raw material. First, copper foil must be
Etched to obtain the required circuit, and the protective film should be drilled to reveal the
Corresponding pad. after cleaning, the two are combined by rolling. Then the exposed part
of the pad electroplated gold or tin to protect. In this way, the big panel board will be ready.
Generally also it's stamped into the corresponding shape of the small circuit board. There is
Also no protective film directly on the copper foil, but printed resistance soldering coating, so
that the cost will be lower, but the mechanical strength of the circuit board will become worse.
unless the strength requirement is not high and the price needs to be as low as possible, it is
Best to apply the protective film method. 

Double layer structure: when the circuit is too complex to be wired, or copper foil is needed to
Shield the ground, it is necessary to choose a double layer or even a multilayer. the most typical
Difference between a multilayer and a single plate is the addition of a perforated structure to
Connect the layers of copper foil. the first process of transparent rubber + base material +
Copper foil is to make holes. Drill holes in the base material and copper foil first, clean and
Then plated with a certain thickness of copper. The subsequent fabrication process is almost
the same as the single-layer circuit. 

Double sided structure: both sides of the double sided FPC have pads, mainly used to connect
Other circuit boards. Although it and monolayer structure is similar, but the manufacturing
Process is very different. Its raw material is copper foil, protective film and transparent glue.
the protective film should be drilled according to the position of the pad first, then the copper
Foil should be affixed, the pad and track lines should be etched and then the protective film of
Another drilled hole should be affixed.

Copper foil is available in two different types of copper:
ED Copper and RA copper.
ED copper is an electro-deposited (ED) copper foil produced in the same way as the copper
Foil used for rigid printed circuit boards. this also means that the copper is " treated", i.e., it
Has a slightly rough surface on one side, which ensures a better adhesion when the copper
Foil is bonded to the base material.
RA copper is a rolled and annealed copper foil produced from electrolytically deposited
Cathode copper, which is melted and cast into ingots. the ingots are first hot-rolled to
A certain size and milled on all surfaces. the copper is then cold-rolled and annealed,
Until the desired thickness is obtained.
Copper foil is available in thickness of 12, 18, 35 and 70 m.

the most common available for dielectric substrate and coverlay is polyimide films. this
Material can also be used as coverlay. Polyimide is best suited for flexible circuits because
of its characteristics as stated below:
    High temperature resistance allows soldering operations without damaging the flexible
    circuits
    Very good electrical properties
    Good chemical resistance
Polyimide is available in thicknesses of 12.5, 20, 25 and 50 m.

Base laminates for rigid printed circuit boards are copper foils laminated together with the
Base materials, the adhesive coming from the prepreg material during lamination. Contrary
to this is the flexible circuit where the lamination of the copper foil to the film material is
Achieved by means of an adhesive system. It is necessary to distinguish between two main
Systems of adhesive, namely thermoplastic and thermoset adhesives. The choice is dictated
Partly by the processing, and partly by the application of the finished flexible circuit.



FPC Case: Flexible PCBs | Thin PCBs | Polyimide PCBs|
Single Sided FPC
(FPC's are custom-made products, the picture and parameters shown are just for reference)


General description
this is a type of single layer flexible printed circuit for the application of Wireless Dongle,
0.2mm thick. the base laminate is from ITEQ, It's fabricated per IPC 6012 Class 2 using
Supplied Gerber data. Polyimide stiffener is applied on the inserting head.


Parameter and data sheet

Size of Flexible PCB	230.5 X 40.8mm
Number of Layers	1
Board Type	Flexible PCB
Board Thickness	0.20mm
Board Material	Polyimide (PI) 25m
Board Material Supplier	ITEQ
Tg Value of Board Material	60
PTH Cu thickness	20 m
Inner Iayer Cu thicknes	N/A
Surface Cu thickness	35m (1oz)
Coverlay Colour	Yellow
Number of Coverlay	1
Thickness of Coverlay	25 m
Stiffener Material	Polyimide
Stiffener Thickness	0.2mm
Type of Silkscreen Ink	IJR-4000 MW300
Supplier of Silkscreen	TAIYO
Color of Silkscreen	White
Number of Silkscreen	1
Peeling test of Coverlay	No peelable
Legend Adhesion	3M 90 No peeling after Min. 3 times test
Surface Finish	Immersion Gold
Thickness of Nickle/Gold	Au: 0.03m(Min.); Ni 2-4m
RoHS Required	Yes
Famability	94-V0
Thermal Shock Test	Pass, -25125, 1000 cycles.
Thermal Stress	Pass, 3005,10 seconds, 3 cycles. No delamination, no Blistering.
Function	100% Pass electrical test
Workmanship	Compliance with IPC-A-600H & IPC-6013C Class 2

Features and benefits
Excellent flexibility
Reducing the volume
Weight reduction
Consistency of assembly
Increased reliability
Controllability of electrical parameter design
the end can be whole soldered
Material optionality
Low cost
Continuity of processing
Focus on low to medium volume production
More than 15 years of experience


Application
Antenna FPC, flex keyboard, Industrial control computer soft board


Variety of PCBs


X-ray target shooting