| After-sales Service Provided: | Engineers available to service machinery overseas |
|---|---|
| Warranty: | 1 year |
| Voltage: | 380hz we can make it according to customers' Local voltage according t |
| Brand Name: | XBF |
| Condition: | New |
Quick Details
Specifications
Energy Saving High Quality Air Energy Dryer for Tea Product
1.Product Introduction:
1.Product Introduction:
TheAir heat pump dryer is finned evaporator, compressor, fin condenser (machine) and expansion valve of four parts, by making the working medium continuously complete evaporation (absorb heat from the outdoor environment) to compression, condensation (gives off heat drying room) indoors to throttle, thermodynamic cycle process of evaporation, again to the external environment at low temperature in the heat transfer to the drying room, under the action of refrigerant in the compressor circulating in the system.It made within the compressor gas booster heating process (temperature up to 100℃), it enters the release of the high-temperature heat drying room air, while being cooled and translated into flow liquid when it runs to the outside machine, rapid heat evaporating liquid into a gas again, at the same time, the temperature can fall to - 20 ℃~ 30 ℃, then the air surrounding the heat absorber will continue to transfer heat to the refrigerant.
2.Principle
High temperature heat pump dryer is to use the inverse carnot principle, absorb free heat in the air and transfer it to the drying warehouse, to achieve the drying room temperature increase, with the corresponding dehumidification and drainage equipment to achieve the drying of materials.Heat pump dryer by compressor - heat exchanger (internal machine) - throttling device - heat receiver (external machine) - compressor and other devices constitute a refrigerant circulation system.under the action of refrigerant in the compressor circulating in the system, it made within the compressor gas booster heating process (temperature up to 100 ℃), it enters the release of the high-temperature heat drying room air, while being cooled and translated into flow liquid when it runs to the outside machine, liquid evaporation heat quickly again into gas, the temperature dropped to minus 30 ℃, 20 ℃, the air surrounding the heat absorber will continue to transfer heat to the refrigerant.The continuous circulation of refrigerant realizes the transfer of heat from the air to the drying room to heat the air temperature in the room to achieve the purpose of drying materials.5. Waste heat recovery system: the drying system has a total of 3 waste heat recovery lines, which can minimize the loss of heat and achieve high efficiency. Model XBF-100AB/AB1 XBF-100DB1 XBF-100GB/GB1 Power 1.0kw 1.0kw 1.0kw Highest wind tempetature 65C 65C 80C Best wind tempetature 55C~63C 35C~55C 65C~78C Suitable environmental temperature -20C~+40C -20C~+40C -20C~+40C Dewaterability ≥3.0kg/h (T50C,M80%) ≥3.0kg/h (T50C,M80%) ≥3.0kg/h (T50C,M80%) Tray Size(mm) 780*510*40 780*510*40 780*510*40 Size(mm) 1180*680*1820 1180*680*1820 1180*680*1820
3.Product picture:
4.the Technical Parameters of Dryer:
5.the advantages of dryers:
(1) stable, not restricted by the weather: whether cloudy days and rainy days, day and night, wind and snow, all-weather stable operation.
(2). Energy saving and high efficiency: using clean electric energy to work, the drying operation cost is only 40% of oil drying equipment, 60% of coal drying machine and 30% of electric heating drying machine, saving more than 60% of enErgy compared with ordinary drying equipment.A closed dehumidification mode is adopted, without discharging waste heat to the outsideWorld.Patented level 3 waste heat recovery technology, rapid discharge of water while your heat loss.
(3). Good effect: the finished product after drying has a good appearance;High active components;Uniform drying, 360 degrees without dead Angle drying.
(4). Small footprint and easy installation: the equipment only needs a small installation site;Drying room on site assembly is simple and convenient.
6.Composition of heat pump drying system:
(1). Main machine (heating system): absorbs free heat from the air with little electric energy input, and USES it to dry materials.
(2), drying room: used for placing materials, and insulation to avoid heat loss.
(3). Circulating air system: bring heat to every corner of the drying room to raise the temperature of the drying room, and take away moisture from the materials.
(4). Moisture drainage system (drying system): the purpose of drying is to discharge the moisture with high humidity in the drying room.
(5). Waste heat recovery system: the drying system has a total of 3 waste heat recovery lines, which can minimize the loss of heat and achieve high efficiency.
(6). Drainage system: condensate water is discharged to the outdoor to avoid increasing the humidity of indoor air.
(7), programmable intelligent control system: according to the most appropriate drying process curve, automatic adjustment of temperature and humidity, drying time, intelligent operation.
7.Product Materials Show:
A. Technical service
1, We calculate the capacity and recommend the best models.
2, We supply you the professional refrigeration technical support and electronic technical support for your installation, debugging and operation.
3, We supply the spare parts and technical support in & after the warranty time.
4, We supply the training course to your workers at our factory if you need.
B. after-sales service
1, Technical support for your installation, operation and maintenance.
2, One year's warranty, and you can pay for extended warranty.
3, Spare parts and technical support at most economic prices after the warranty.
9.Delivery and Package
for heat pump dryer parts---with plywood
for drying chamber +trolleys
If shipped with 20ft container or 40ft container, no packing
If shipped with LCL( less than container load), packed in plywood
If you want to cooperate with our company, please contact me
