Industrial Fungus Special Dried Fruit Air-Energy Heat Pump Dryer

1.Product Introduction

the air heat pump dryer is finned evaporator, compressor, fin condenser (machine) and expansion valve of four parts, by making the working medium continuously complete evaporation (absorb heat from the outdoor environment) to compression, condensation (gives off heat drying room) indoors to throttle, thermodynamic cycle process of evaporation, again to the external environment at low temperature in the heat transfer to the drying room, under the action of refrigerant in the compressor circulating in the system.It made within the compressor gas booster heating process (temperature up to 100℃), it enters the release of the high-temperature heat dryiNg room air, while being cooled and translated into flow liquid when it runs to the outside machine, rapid heat evaporating liquid into a gas again, at the same time, the temperature can fall to - 20 ℃~ 30 ℃, then the air surrounding the heat absorber will continue to transfer heat to the refrigerant.

2.Principle:
this drying machine use of heat pump evaporator absorbs heat from the outside air.Or recycling of exhaust gas residual heat in the process of drying.through the work of compressor, the energy transport (transfer) to drying box, drying box of hot air after repeated cyclic heating, absorb the moisture in the material, its cooling humidification, through hot air platoon is wet or the process of condensation, water take the moisture out of the material, and finally realizes the continuous drying of materials.




3.Product Pictures:

4.Composition of heat pump drying system:

1. Main machine (heating system): absorbs free heat from the air with little electric energy input, and USES it to dry materials.

2, drying room: used for placing materials, and insulation to avoid heat loss.

3. Circulating air system: bring heat to every corner of the drying room to raise the temperature of the drying room, and take away moisture from the materials.

4. Moisture drainage system (drying system): the purpose of drying is to discharge the moisture with high humidity in the drying room.

5. Waste heat recovery system: the drying system has a total of 3 waste heat recovery lines, which can minimize the loss of heat and achieve high efficiency.

5.the advantages of dryers:

1, stable, not restricted by the weather: whether cloudy days and rainy days, day and night, wind and snow, all-weather stable operation.

2. Energy saving and high efficiency: using clean electric energy to work, the drying operation cost is only 40% of oil drying equipment, 60% of coal drying machine and 30% of electric heating drying machine, saving more than 60% of energy compared with ordinary drying equipment.A closed dehumidification mode is adopted, without discharging waste heat to the outside world.Patented level 3 waste heat recovery technology, rapid discharge of water while your heat loss.

3. Simple operation and convenient maintenance: personalized man-machine interface, touch screen programmable controller, one-button start, simple, beautiful and high-grade;Easy maintenance, only need regular cleaning heat exchanger.

4, multifunctional application: drying, dehumidification, dehumidification, cold air drying (especially suitable for perishable materials), programmable control.Applicable to medicinal materials drying, food drying, agricultural products drying, wood drying, industrial products drying, sludge drying, line drying, energy-saving transformation drying and so on. 

6.the Technical Parameters:

Model	XBF-100AB/AB1	XBF-100DB1	XBF-100GB/GB1
Power	1.0kw	1.0kw	1.0kw
Highest wind tempetature	65C	65C	80C
Best wind tempetature	55C~63C	35C~55C	65C~78C
Suitable environmental temperature	-20C~+40C	-20C~+40C	-20C~+40C
Dewaterability	≥3.0kg/h  (T50C,M80%)	≥3.0kg/h  (T50C,M80%)	≥3.0kg/h  (T50C,M80%)
Tray Size(mm)	780*510*40	780*510*40	780*510*40
Size(mm)	1180*680*1820	1180*680*1820	1180*680*1820

7.Products Details Show:

8.Our Service

A. Technical service
1, We calculate the capacity and recommend the best models.
2, We supply you the professional refrigeration technical support and electronic technical support for your installation, debugging and operation.
3, We supply the spare parts and technical support in & after the warranty time.
4, We supply the training course to your workers at our factory if you need.
B. after-sales service
1, Technical support for your installation, operation and maintenance. 
2, One year's warranty, and you can pay for extended warranty.
3, Spare parts and technical support at most economic prices after the warranty.

9.Delivery and Package:

  for heat pump dryer parts---with plywood
  for drying chamber +trolleys
  If shipped with 20ft container or 40ft container, no packing
  If shipped with LCL( less than container load), packed in plywood

10.Company Profile

Jinan xinbeifa machinery equipment co., LTD. Has professional designers, experienced technicians and first-class processing equipment, for the manufacture of naive equipment identification a solid foundation. with years of experience, our company has independently developed a variety of expanded food equipment and front and rear end auxiliary equipment, the product sales throughout the country all provinces, cities, autonomous regions, more exports to Australia, the Netherlands, Pakistan, Malaysia, myanmar and other Asian, European, American countries.. Our company adhering to the "professional casting quality, integrity to win the future" business purposes;In the principle of mutual benefit and common development, based on a high starting point, large investment, high 

Level of operation;Adhere to high standards, zero defects, refined production standards, ensure that every production link, to create a safe and high-quality brand.

If you are interested in our heat pump dryer, please contact us for more information, such as catalogue, video,etc.