PTO Shaft to fit New Holland Dis Mower Discbines

Our drive shafts for PTO can be adjusted to the following models of disc mowers:

New Holland Discbines 1431and 1432 Model 411 1409, 1410 1411 14, 1411, 1441, 1442 14, 1431, 143
H7220, H7230, H7320, H7330, H7450, H7460, H7550, H7560
IH DC 132, Case IH DC 132

Parts of Pto Shafts. Pto Shaft
It is important to know the dimensions, measurements horsepower, sizes, and the agriculture PTO shaft components in order to select the right PTO shaft for your farm equipment. Although the U-joints and yokes are required for operation however, the safety chains as well as the shield are vital components in the PTO shaft to ensure you are secure during operation.

Internal Yoke: There are two located on both sides of the PTO shaft: implement and tractor. It is joined on the end of the drive.
Universal Joint- There are two joints at both ends of the PTO shaft.
External Yoke- There is a second on both sides on the PTO shaft. It's got an "Y" shape that connects to the U-joint, and an opening for females.
Safety Chains - the chains ensure the PTO shaft to the equipment as well as the tractor.
Safety ShieldCones placed at both the ends.
Different Models PTO Shaft for Sale
Every discipline has several PTO shafts as well as the combination clutch.

the different types of PTO shafts and locations for clutches differ from model to model.

Models below were initially fitted by Weasler as well as Bondioli & Pavesi PTO shafts.

Part Number	Tractor	Implement	Description
New Holland Discbines 1431, 1432
14656853	1.375-21	1.5" x 23 spline	55N 80x50 Double CV
82-14656853	none	1.5" x 23 spline	55N 50 degrees CV half(implement)
83-14656853	1.375-21	none	55N 80 degrees CV half(tractor)
83-14756853	1.750-20	none	55N 80 degrees CV half(tractor)
New Holland Discbines Model 411
14656853	1.375-21	1.5" x 23 spline	55N 80x50 Double CV
82-14656853	none	1.5" x 23 spline	55N 50 degrees CV half(implement)
83-14656853	1.375-21	none	55N 80 degrees CV half(tractor)
83-14756853	1.750-20	none	55N 80 degrees CV half(tractor)
857-5521	none	1.375-21	55N 50 degrees CV clamp yoke only
New Holland Discbines 1409, 1410, 1411, 1412, 1441, 1442
55N-NH14XX-DISCBINE	1.375-6	none	CAT6 CV with 1.375-21 yoke
14656848	1.375-21	none	55N CV without implementing yoke
14756848	1.750-20	none	55N CV without implementing yoke
New Holland Discbines H7220, H7230, H7320, H7330, H7450, H7460, H7550, H7560
14605548	1.375-21	none	55N CV without implementing yoke
14705548	1.375-21	none	55N CV without implementing yoke

Model:	Primary	Intermediate	Secondary	HP	RPM
H7220	35N CV		35N Square	65	540
H7230	55N CV or standard	Jack style 1.375-21	H8 double CV	80	540/1000
H7320	35N CV		35N Square	65	540
H7330	55N CV or standard	Jack Style 1.375-21	H8 double CV	80	540/1000
H7450	55N Double 80/50 CV or 55N standard (for swivel)		55N standard	90	1000
H7460	55N Standard	55N Square w/clutch	55N Standard	100	1000
H7550	55N Double 80/50 CV or 55N standard (for swivel)	55N standard	55N standard	90	1000
H7560	55N Standard	55N Square w/clutch	55N standard	100	1000

Three Different Shafts for Pto. Shafts
the kind of PTO shaft you pick will depend on the task you're expected to perform. If you're plowing or mowing or shredding, you'll need an PTO shaft that is suitable for every task. It will also help safeguard your machinery from excessive stress, hits or tension.

Non-Shear PTO Shaft
this design is for equipment that is not intended to withstand sudden stops. It's a yoke-to yoke arrangement. this is a good option for larger mowers as the motions should be smooth, as there won't need to be any moments that are obstructed or stopped.

Shear Pin PTO Shaft
the end yoke comes in two pieces and utilizes a shear pin to keep them in place for operation. The pin absorbs shock when there is sudden stop in order to prevent damage to the driveline. It can be utilized in conjunction with other equipment, such as chippers.

Slip Clutch PTO Shaft
Slip Clutch is made to shield your tractor and the attached equipment from being damaged due to internally sliding- which allows the movement of an object when it hits. for instance, when changes in the season, stones and rocks are brought to the surface and when they are struck you need the impact to be absorbed so that you won't cause damage to the gearbox.

PTO Shaft Length Limit
Its Power Take off (PTO) shaft is the part that supplies energy to your device. Therefore, it is vital to know how it functions to ensure safety for the user. It is also crucial for you to know the maintenance specifications to avoid mechanical issues. PTO shafts are rated but are not interchangeable with tractors or other implements. It is crucial to attach the right shaft to the machine in accordance with the specifications of the manufacturer and ensure that it's the correct length.

Length: the length of the PTO shaft is measured when installing an implement on an tractor in the very first. If a shorter PTO shaft is needed then the operator should follow the formula supplied by the supplier in order to trim the shaft according to its proper length. this is typically accomplished by measuring the output shaft of the tractor and putting the input shaft so that the PTO shaft is at its narrowest.
Too long When your shaft for the PTO is excessively long (or in the event that the telescopic tubes are seized), "end thrust" may occur. this could ruin your tractor's internal PTO drive, or the clutch for your implement and gearbox, possibly invalidating your warranty.
Too short: If the shaft is too long it may break away from the device, creating serious safety risks and causing injury.
how can I cut the PTO Shaft in the Correct Length?
When your PTO shaft gets too big, the shaft may be unable to move during the lifting of the 3-point hitch. the damage could be to the chipper's bearing and the PTO in the tractor. In the event that it is found that the PTO shaft becomes too large, it should be cut. Equal amounts should be cut to shorten both PTO half.

1. Install the chipper on the three-point hitch on the tractor.

2. Cut the engine off and remove the keys. Then lower the chipper onto an even and solid surface.

3. Take the 3-point hitch up up so that the shaft for power intake for the crusher is the same height that the power intake shaft of the tractor. this will ensure that both the PTO along with the power intake shaft should be in the closest proximity in this position.

4. Remove the PTO shaft off. Connect one end of the shaft with the chipper to ensure that you can lock the pin. Secure. Set the opposite portion of the shaft at an end of the tractor's PTO. Place the other end of the chipper on the side. Mark in the shield how much has to be removed. The tubes need to be cut to a length that they can't be able to reach the bottom from the chipper positions.

5. Slice the tube of plastic.

6. Cut a piece of the profile tube. It should be the same length as the one you removed from the shield. Cut the other half of the PTO shaft to be the same length.

7. Cut sharp edges off of the tubes for profile.

PTO Shaft Maintenance
the PTO shaft must be lubricated regularly to prevent universal joint in good condition and also to stop the shaft from sizing. Inability to grease your shaft on a regular basis or in accordance with the guidelines stipulated in the PTO maintenance schedule of the shaft can cause end thrust, which could lead to damaging the gearbox of the implement. It is advised to grease standard universal joints once every twenty hours, or 8 hours in extreme circumstances. Remember! Grease travels the simplest route through internal ports that lead to four bearings. Poor quality and overheated grease that is baked in a single port will block grease from reaching the bearing, and will cause damage to each of the cross bearings.

in the first place, make sure you complete opening the guard cover so that grease gets across all bearings. the small access hole isn't good enough. Also, make sure to check the condition of the PTO security guards. If they're damaged or damaged, you should arrange for replacement while ensuring the safety of the operator.

Agricultural PTO Shafts Applications
We all know that nowadays, everyone places significant importance to farming production particularly in the areas of cultivation, harvesting and maintenance. this is an essential component of improving output. however, we need to discover that our farmlands are not the bustling life of suffering farmers however, a vast portion of the land is cultivated using equipment and machinery. Farmers and individual operators are during the work and this demonstrates the importance to agricultural equipment. There is also the use for PTO shafts for agricultural machines. for instance the mower, sprayer harvester, field return machine, etc. Will have a PTO shaft. but the PTO shaft is different due to different agricultural machinery's various designs and functions. There are a variety of types of HZPT's PTO shafts. You can select the right PTO drive shaft in accordance with the model that is used.

Agricultural Gearbox and PTO Shafts
PTO shafts are employed in agricultural equipment like tractor, combines and harvesters. these parts are subject to high stress and loads and it is crucial to determine why they have failed in the first place. Continuous shaft compression could cause damage to connecting shafts, as well as the tractor and equipment. A PTO shaft used in the agricultural gearbox can be an essential element of a farming equipment or tractor. and the PTO shaft used in an agriculture gearbox is secured by an safety shield on each end and is seen on tractor and implements. The PTO shaft is welded to the drive side using the universal joint, and the rear shaft may be connected straight to the tractor.

If you are also in need of agricultural gearboxes, be in touch!

PTO Shaft Suppliers
HZPT is an industrial business that combines precision casting, precision forging and machine machining. the company owns over 100 pieces of equipment, such as milling, turning, grinding, planning drawing, numeric control low frequency electrical furnaces, casting lines 1000 ton friction presses coating line, etc. the company is primarily involved in the production of the universal joints for agricultural machines transmission shaft assembly the transmission shaft of agricultural machines, agricultural transmission shaft Plow shaft assemblies, Spline shaft precision casts, forgings for dies and other items. The range of products includes more than 100 different varieties of 11 series, including pulpers, rotary cultivators lawnmowers, field returning machines and more. It produces an annual volume in excess of 120000 pieces of universal agricultural machinery joint assemblies, 4000 tonnes of precise castings and 4000 tonnes of metal forgings. The company is committed to the company's ethos of "people-oriented co-operation, unity and unity quality." In accordance with the corporate tenet that "quality results, honest and trustworthiness, first for the customer." Establish the corporate policy of "taking the needs of the customer as the main goal" to offer friendly customer service.

We look forward to working with both our old and new customers to develop joint projects!